Removal
LIGHTING: TURN SIGNAL FLASHER ASSEMBLY: REMOVAL
1. TABLE OF BOLT, SCREW AND NUT Removal
2. REMOVE COWL TOP VENTILATOR LOUVER RH Removal
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
(a) Disable the AUTO TILT AWAY function by changing the customize parameter Programming and Relearning.
NOTICE:
Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the current setting after finishing the operation.
HINT
Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.
(b) Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column.
(c) Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
NOTICE:
* w/ Navigation System (for HDD):
After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal:
* When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.
4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH Removal
5. REMOVE INSTRUMENT PANEL FINISH PANEL END LH Removal
6. REMOVE SHIFT LEVER KNOB Removal
7. REMOVE NO. 3 BOX PANEL Removal
8. REMOVE REAR CONSOLE PANEL UPPER Removal
9. REMOVE CONSOLE PANEL SUB-ASSEMBLY UPPER Removal
10. REMOVE CONSOLE REAR END PANEL Removal
11. REMOVE CONSOLE COVER LOWER Removal
12. REMOVE CONSOLE BOX ASSEMBLY Removal
13. REMOVE SWITCH AND VOLUME CASE Removal
14. REMOVE NO. 2 STEERING WHEEL COVER LOWER Removal
15. REMOVE STEERING PAD ASSEMBLY Removal
16. REMOVE STEERING WHEEL ASSEMBLY Removal
17. REMOVE STEERING COLUMN COVER (w/o Driver Monitor Camera) Removal
18. REMOVE STEERING COLUMN COVER (w/ Driver Monitor Camera) Removal
19. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE Removal
20. REMOVE INSTRUMENT CLUSTER FINISH PANEL Removal
21. REMOVE COMBINATION METER ASSEMBLY Removal
22. REMOVE INSTRUMENT SIDE PANEL LH Removal
23. REMOVE NO. 1 INSTRUMENT CLUSTER MOULDING Removal
24. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER Removal
25. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD Removal
26. REMOVE NO. 1 INSTRUMENT PANEL LOWER AIRBAG Removal
27. REMOVE INSTRUMENT SIDE PANEL RH Removal
28. REMOVE NO. 2 INSTRUMENT CLUSTER Removal
29. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER Removal
30. REMOVE INSTRUMENT PANEL LOWER Removal
31. REMOVE NO. 2 INSTRUMENT PANEL LOWER AIRBAG Removal
32. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY Removal
33. REMOVE RADIO RECEIVER ASSEMBLY Removal
34. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Navigation System) Removal
35. REMOVE MULTI-DISPLAY ASSEMBLY WITH BRACKET (for DVD) Removal
36. REMOVE DISPLAY AND NAVIGATION ASSEMBLY WITH BRACKET (for HDD) Removal
37. REMOVE FRONT PILLAR GARNISH RH Removal
38. REMOVE FRONT PILLAR GARNISH LH Removal
39. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL Removal
40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH) Removal
41. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL Removal
42. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH) Removal
43. REMOVE NO. 1 SPEAKER HOLE COVER Removal
44. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY Removal
45. REMOVE TIRE PRESSURE WARNING ECU Disassembly
46. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY Removal
47. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY Removal
48. REMOVE INSTRUMENT PANEL SAFETY PAD Removal
49. REMOVE TURN SIGNAL FLASHER ASSEMBLY
(a) Detach the clip.
(b) Disconnect the connector and remove the turn signal flasher.