Installation

INTERIOR: ROOF HEADLINING: INSTALLATION

1. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Install the front door opening trim weatherstrip LH as shown in the illustration.

2. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Install the front door opening trim weatherstrip RH as shown in the illustration.

3. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Install the rear door opening trim weatherstrip LH as shown in the illustration.

4. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Install the rear door opening trim weatherstrip RH as shown in the illustration.

5. INSTALL NO. 1 ROOF WIRE (w/o Sliding Roof)

(a) Install the roof wire.

(1) Remove the peeling paper from one side of double-sided tape.

(2) Attach double-sided tape to the marks on the roof headlining, as shown in the illustrations below above.

(3) Remove peeling paper from the other side of double-sided tape.

(4) Align the wire harness to double-sided tape. Also, align the marking tape areas of the wire harness to the marks on the roof headlining. Temporarily attach the wire harness to the roof headlining. Secure the wire harness to the roof headlining with vinyl tape.

NOTICE:
Securely install the No. 1 roof wire. If the wire is not secure, noise will occur.

6. INSTALL NO. 1 ROOF WIRE (w/ Sliding Roof)

(a) Install the roof wire.

(1) Remove the peeling paper from one side of double-sided tape.

(2) Attach double-sided tape to the marks on the roof headlining, as shown in the illustrations above.

(3) Remove peeling paper from the other side of double-sided tape.

(4) Align the wire harness to double-sided tape. Also, align the marking tape areas of the wire harness to the marks on the roof headlining. Temporarily attach the wire harness to the roof headlining. Secure the wire harness to the roof headlining with vinyl tape.

NOTICE:
Securely install the No. 1 roof wire. If the wire is not secure, noise will occur.

7. INSTALL VANITY LIGHT ASSEMBLY

(a) Engage the 3 claws and install the vanity light assembly.

HINT
Use the same procedure to install the light on the other side.

8. INSTALL ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the roof silencer pads and install the pads using double-sided tape as shown in the illustration.

9. INSTALL REAR SIDE RAIL SPACER (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the rear side rail spacer and install the spacers using double-sided tape as shown in the illustration.

10. INSTALL ROOF HEADLINING PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the roof headlining pad and install the pads using double-sided tape as shown in the illustration.

11. INSTALL REAR SIDE RAIL SPACER (w/ Sliding Roof)

(a) Align the markings on the roof headlining assembly with the rear side rail spacer and install the spacers using double-sided tape as shown in the illustration.

12. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

(a) Place the roof headlining in the vehicle from the front right door.

(b) Engage the hook, 10 claws and 2 clips, and install the roof headlining assembly.

(d) Connect each connector to the map light assembly.

13. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) Place the roof headlining in the vehicle from the front right door.

(b) Engage the hook, 10 claws, 8 fasteners and 2 clips, and install the roof headlining assembly.

(d) Connect each connector to the map light assembly.

14. INSTALL VISOR HOLDER

(a) Set the claws of the visor holder as shown in the illustration

(b) Engage the claws and install the visor holder.

HINT
Use the same procedure to install the holder on the other side.

15. INSTALL VISOR ASSEMBLY LH

(a) Install the visor assembly LH with the 2 screws.

16. INSTALL VISOR ASSEMBLY RH

17. INSTALL VISOR BRACKET COVER

(a) Engage the 4 claws and install the visor bracket cover.

HINT
Use the same procedure to install the cover on the other side.

18. INSTALL ASSIST GRIP SUB-ASSEMBLY

(a) Put an assist grip sub-assembly together as shown in the illustration.

(b) Install the assist grip sub-assembly.

HINT
Use the same procedure for the other 3 assist grips.

19. INSTALL COAT HOOK

(a) Install the coat hook with the screw.

HINT
Use the same procedure to install the hook on the other side.

20. INSTALL SPOT LIGHT ASSEMBLY

(a) Connect the connector.

(b) Engage the 2 clips and install the spot light assembly.

21. INSTALL MAP LIGHT ASSEMBLY (w/o Sliding Roof)

(a) Connect the connector.

(b) Engage the 2 clips and install the map light assembly.

(c) Install the 2 screws.

(d) Engage the 3 claws and close the cover.

22. INSTALL MAP LIGHT ASSEMBLY (w/ Sliding Roof)

(a) Connect the connector.

(b) Engage the 2 clips and 2 claws.

(c) Install the 2 screws to the map light assembly as shown in the illustration.

23. INSTALL RAIN SENSOR TAPE Installation

24. INSTALL RAIN SENSOR Installation

25. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER Installation

26. INSTALL ROOF SIDE INNER GARNISH LH

(a) Engage the claw and 4 clips, and install the roof side garnish inner LH.

27. INSTALL ROOF SIDE INNER GARNISH RH

28. INSTALL REAR SEAT SIDE GARNISH LH

(a) Engage the 5 claws and install the rear seat side garnish LH.

29. INSTALL REAR SEAT SIDE GARNISH RH

30. INSTALL CENTER PILLAR GARNISH LH

(a) Engage the 2 claws and install the center pillar garnish LH.

(b) Install the 2 screws.

31. INSTALL CENTER PILLAR GARNISH RH

32. INSTALL LOWER CENTER PILLAR GARNISH LH

(a) Engage the 5 clips and 3 claws, and install the lower center pillar garnish LH.

33. INSTALL LOWER CENTER PILLAR GARNISH RH

34. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

(a) Install the front seat outer belt assembly LH with the bolt.

Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)

35. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

36. INSTALL LAP BELT OUTER ANCHOR COVER

(a) Engage the 2 claws and install the lap belt outer anchor cover as shown in the illustration.

HINT
Use the same procedure to install the cover on the other side.

37. INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the 2 clips.

(b) Engage the 5 claws and install the rear door scuff plate LH.

38. INSTALL REAR DOOR SCUFF PLATE RH

39. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY (for 2GR-FSE)

40. INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY (for 2GR-FSE)

41. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR (for 2GR-FSE) Installation

42. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 2GR-FSE) Installation

43. INSTALL HEATED OXYGEN SENSOR (for 2GR-FSE) Installation

44. INSTALL FRONT CENTER FLOOR BRACE (for 2GR-FSE) Installation

45. INSTALL REAR NO. 1 FLOOR PANEL BRACE (for 2GR-FSE) Installation

46. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY (for 4GR-FSE 2WD)

47. INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY (for 4GR-FSE 2WD)

48. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR (for 4GR-FSE 2WD) Installation

49. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 4GR-FSE 2WD) Installation

50. INSTALL HEATED OXYGEN SENSOR (for 4GR-FSE 2WD) Installation

51. INSTALL FRONT CENTER FLOOR BRACE (for 4GR-FSE 2WD) Installation

52. INSTALL REAR NO. 1 FLOOR PANEL BRACE (for 4GR-FSE 2WD) Installation

53. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY (for 4GR-FSE 4WD) Installation

54. INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY (for 4GR-FSE 4WD) Installation

55. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR (for 4GR-FSE 4WD) Installation

56. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 4GR-FSE 4WD) Installation

57. INSTALL HEATED OXYGEN SENSOR (for 4GR-FSE 4WD) Installation

58. INSTALL FRONT CENTER FLOOR BRACE (for 4GR-FSE 4WD) Installation

59. INSTALL REAR NO. 1 FLOOR PANEL BRACE (for 4GR-FSE 4WD) Installation

60. INSTALL FLOOR SHIFT LEVER ASSEMBLY (for Manual Transmission)

61. INSTALL SHIFT LEVER CAP (for Manual Transmission)

62. INSTALL NO. 1 SHIFT AND SELECT LEVER BOOT (for Manual Transmission)

63. INSTALL INSTRUMENT PANEL STAY Installation

64. INSTALL INSTRUMENT PANEL CLIP Installation

65. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY Installation

66. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY Installation

67. INSTALL NO. 2 CONSOLE BOX DUCT (for Manual Transmission) Installation

68. INSTALL NO. 1 CONSOLE BOX DUCT (for Automatic Transmission) Installation

69. INSTALL NO. 2 CONSOLE BOX DUCT (for Automatic Transmission) Installation

70. INSTALL FRONT STEREO COMPONENT SPEAKER ASSEMBLY (w/ Front Center Speaker) Installation

71. INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY Installation

72. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY Installation

73. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY Installation

74. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY Installation

75. INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY Installation

76. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Installation

77. INSTALL SIDE INSTRUMENT PANEL RH Installation

78. INSTALL COMBINATION METER ASSEMBLY Installation

79. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Installation

80. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation

81. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY Installation

82. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Installation

83. INSTALL SIDE INSTRUMENT PANEL LH Installation

84. INSTALL FRONT PILLAR GARNISH LH

(a) Remove the protective cover.

(b) Make sure that the front pillar garnish clip is not damaged.

NOTICE:
* If there is any damage, replace the garnish clip with a new one.
* When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

(c) Engage the guide.

(d) Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

HINT
Tape the tips of the needle-nosed pliers before use.

(e) Engage the 2 clips to install the front pillar garnish LH.

85. INSTALL FRONT PILLAR GARNISH RH

86. INSTALL FRONT DOOR OPENING TRIM COVER LH

(a) Engage the 4 claws and install the front door opening trim cover LH.

87. INSTALL FRONT DOOR OPENING TRIM COVER RH

88. INSTALL FRONT DOOR SCUFF PLATE LH (w/o Illumination)

(a) Engage the 4 clips.

(b) Engage the 7 claws, and install the front door scuff plate LH.

89. INSTALL FRONT DOOR SCUFF PLATE RH (w/o Illumination)

90. INSTALL FRONT DOOR SCUFF PLATE LH (w/ Illumination)

(a) Connect the connector.

(b) Engage the 4 clips.

91. INSTALL FRONT DOOR SCUFF PLATE RH (w/ Illumination)

92. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY Installation

93. INSTALL STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column) Installation

94. INSTALL STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column) Installation

95. ADJUST SPIRAL CABLE WITH STEERING SENSOR Installation

96. INSTALL STEERING WHEEL ASSEMBLY Installation

97. INSTALL STEERING PAD Installation

98. INSTALL LOWER NO. 3 STEERING WHEEL COVER Installation

99. INSTALL LOWER NO. 2 STEERING WHEEL COVER Installation

100. INSTALL INTEGRATION CONTROL PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Multi-display) Installation

101. INSTALL DISPLAY AND NAVIGATION MODULE DISPLAY WITH RADIO RECEIVER ASSEMBLY (w/ Multi-display) Installation

102. INSTALL CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL Installation

103. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY Installation

104. INSTALL CONSOLE BOX Installation

105. INSTALL CONSOLE BOX REGISTER ASSEMBLY (w/ Ashtray) Installation

106. INSTALL CONSOLE BOX REGISTER ASSEMBLY (w/o Ashtray) Installation

107. INSTALL FRONT ASH RECEPTACLE BOX SUB-ASSEMBLY (w/ Ashtray) Installation

108. INSTALL INSTRUMENT PANEL BOX ASSEMBLY (w/o Ashtray) Installation

109. INSTALL FRONT CONSOLE PANEL SUB-ASSEMBLY (for Manual Transmission) Installation

110. INSTALL REAR CONSOLE PANEL SUB-ASSEMBLY (for Manual Transmission) Installation

111. INSTALL CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transmission) Installation

112. INSTALL UPPER NO. 2 CONSOLE PANEL GARNISH (for Automatic Transmission) Installation

113. INSTALL UPPER NO. 1 CONSOLE PANEL GARNISH (for Automatic Transmission) Installation

114. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission) Installation

115. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transmission) Installation

116. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat) Installation

117. INSTALL REAR INNER SEAT TRACK COVER LH (for Power Seat)

118. INSTALL REAR OUTER SEAT TRACK COVER LH (for Power Seat)

119. INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH (for Power Seat)

120. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH (for Power Seat)

121. INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

122. INSTALL REAR INNER SEAT TRACK COVER RH (for Power Seat)

123. INSTALL REAR OUTER SEAT TRACK COVER RH (for Power Seat)

124. INSTALL FRONT INNER SEAT TRACK BRACKET COVER RH (for Power Seat)

125. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER RH (for Power Seat)

126. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)

127. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat) Installation

128. INSTALL REAR INNER SEAT TRACK COVER LH (for Manual Seat) Installation

129. INSTALL REAR OUTER SEAT TRACK COVER LH (for Manual Seat) Installation

130. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH (for Manual Seat) Installation

131. INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH (for Manual Seat) Installation

132. INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

133. INSTALL REAR INNER SEAT TRACK COVER RH (for Manual Seat)

134. INSTALL REAR OUTER SEAT TRACK COVER RH (for Manual Seat)

135. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER RH (for Manual Seat)

136. INSTALL FRONT INNER SEAT TRACK BRACKET COVER RH (for Manual Seat)

137. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)

138. INSTALL REAR SEATBACK ASSEMBLY Installation

139. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

140. INSTALL REAR SEAT HEADREST ASSEMBLY

141. INSTALL REAR SEAT CUSHION ASSEMBLY Installation

142. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

143. CHECK SRS WARNING LIGHT

Diagnosis System

144. CHECK FOR EXHAUST GAS LEAKS

If exhaust gas is leaking, tighten the related parts to stop the leak. Replace damaged parts as necessary.

145. INSPECT FRONT SEAT ASSEMBLY (for Power Seat) Installation

146. INSPECT SLIDE ADJUSTER LOCK (for Manual Seat)

147. ADJUST SHIFT LEVER POSITION (for 2GR-FSE)

148. INSPECT SHIFT LEVER POSITION (for 2GR-FSE)

149. ADJUST SHIFT LEVER POSITION (for 4GR-FSE 2WD)

150. INSPECT SHIFT LEVER POSITION (for 4GR-FSE 2WD)

151. ADJUST SHIFT LEVER POSITION (for 4GR-FSE 4WD) Adjustments

152. INSPECT SHIFT LEVER POSITION (for 4GR-FSE 4WD) Initial Inspection and Diagnostic Overview