Installation

LIGHTING: AUTOMATIC LIGHT CONTROL SENSOR: INSTALLATION

INSTALLATION

1. INSTALL AUTOMATIC LIGHT CONTROL SENSOR





(a) Attach the 2 claws and install the automatic control sensor.
(b) Connect the connector.
2. INSTALL DEFROSTER NOZZLE ASSEMBLY Reassembly
3. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT Reassembly
4. INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT Reassembly
5. INSTALL INSTRUMENT PANEL SAFETY PAD Installation
6. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY Installation
7. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY Installation
8. INSTALL TIRE PRESSURE WARNING ECU Reassembly
9. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY Installation
10. INSTALL NO. 1 SPEAKER HOLE COVER Installation
11. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH) Installation
12. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL Installation
13. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH) Installation
14. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL Installation
15. INSTALL FRONT PILLAR GARNISH LH Installation
16. INSTALL FRONT PILLAR GARNISH RH Installation
17. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (W/O Navigation System) Installation
18. INSTALL MULTI-DISPLAY ASSEMBLY WITH BRACKET (for DVD) Installation
19. INSTALL DISPLAY AND NAVIGATION ASSEMBLY WITH BRACKET (for HDD) Installation
20. INSTALL RADIO RECEIVER ASSEMBLY Installation
21. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY Installation
22. INSTALL NO. 2 INSTRUMENT PANEL LOWER AIRBAG Installation
23. INSTALL INSTRUMENT PANEL LOWER Installation
24. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER Installation
25. INSTALL NO. 2 INSTRUMENT CLUSTER Installation
26. INSTALL INSTRUMENT SIDE PANEL RH Installation
27. INSTALL NO. 1 INSTRUMENT PANEL LOWER AIRBAG Installation
28. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD Installation
29. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER Installation
30. INSTALL NO. 1 INSTRUMENT CLUSTER MOULDING Installation
31. INSTALL INSTRUMENT SIDE PANEL LH Installation
32. INSTALL COMBINATION METER ASSEMBLY Removal
33. INSTALL INSTRUMENT CLUSTER FINISH PANEL Installation
34. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE Installation
35. INSTALL STEERING COLUMN COVER (W/O Driver Monitor Camera) Installation
36. INSTALL STEERING COLUMN COVER (W/ Driver Monitor Camera) Installation
37. INSTALL STEERING WHEEL ASSEMBLY Installation
38. INSTALL STEERING PAD ASSEMBLY Installation
39. INSTALL NO. 2 STEERING WHEEL COVER LOWER Installation
40. INSTALL WITCH AND VOLUME CASE Installation
41. INSTALL CONSOLE BOX ASSEMBLY Installation
42. INSTALL CONSOLE COVER LOWER Installation
43. INSTALL CONSOLE REAR END PANEL Installation
44. INSTALL CONSOLE PANEL SUB-ASSEMBLY UPPER Installation
45. INSTALL REAR CONSOLE PANEL UPPER Installation
46. INSTALL NO. 3 BOX PANEL Installation
47. INSTALL SHIFT LEVER KNOB Installation
48. INSTALL INSTRUMENT PANEL FINISH PANEL END LH Installation
49. INSTALL INSTRUMENT PANEL FINISH PANEL END RH Installation
50. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE:
Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter Programming and Relearning.

51. INSTALL COWL TOP VENTILATOR LOUVER RH Installation
52. CHECK SRS WARNING LIGHT
(a) Check the SRS warning light Diagnosis System.
53. PERFORM INITIALIZATION
(a) Perform initialization Repair Instruction - Initialization.
NOTE:
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.