FREE REPAIR MANUALS & LABOR GUIDES 1982-2013 Vehicles
Courtesy of Operation CHARM: Car repair manuals for everyone.
Home >> Toyota >> 2011 >> Avalon V6-3.5L (2GR-FE) >> Repair and Diagnosis >> Instrument Panel, Gauges and Warning Indicators >> Dashboard / Instrument Panel >> Service and Repair >> Removal and Replacement >> Installation (from 12/2010)

Installation (from 12/2010)





INSTRUMENT PANEL: INSTRUMENT PANEL SAFETY PAD: INSTALLATION

1. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

(a) Engage the 5 pins.





Text in Illustration





(b) Install the 2 bolts (A) and 2 nuts (F).

Bolt A - Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)

(c) Engage each clamp.

(d) Connect each connector.

2. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY Installation (from 12/2010)

3. INSTALL TIRE PRESSURE MONITOR ECU Installation (from 12/2010)

4. INSTALL FRONT PILLAR GARNISH LH Installation (from 12/2010)

5. INSTALL FRONT PILLAR GARNISH RH Installation (from 12/2010)

6. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY

7. INSTALL NO. 1 SPEAKER HOLE COVER

(a) Engage the 12 claws to install the No. 1 speaker hole cover.





8. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

(a) Engage the 2 clips.

(b) Install the lower center instrument panel finish panel with the 2 screws (E).

9. INSTALL FRONT CONSOLE BOX

(a) Engage the 2 claws.

(b) Install the front console box with the 2 nuts (F) and screw (E).

10. INSTALL CONSOLE BOX ASSEMBLY

(a) Install the console box assembly with the 2 bolts (D) and 2 screws (E).

(b) Connect each connector.

11. INSTALL CONSOLE BOX CARPET

(a) Install the console box carpet.

12. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

(a) Connect each connector.





(b) Engage the 10 clips to install the upper console panel sub-assembly.

(c) Engage the 6 claws to install the upper console box.





13. INSTALL SEAT HEATER SWITCH (w/ Seat Heater System)

(a) Connect the connector.

(b) Engage the 4 claws to install the seat heater switch.





14. INSTALL POSITION INDICATOR HOUSING ASSEMBLY

(a) Engage the 5 claws to install the position indicator housing assembly.





15. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

(a) Turn the shift lever knob clockwise to install the shift lever knob sub-assembly.





16. INSTALL INSTRUMENT SIDE PANEL RH

(a) Engage the claw, 2 clips and 3 guides to install the instrument side panel RH.

17. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH

(a) Engage the 3 claws and clip.

(b) Install the lower instrument panel finish panel RH with the bolt (B) or (C) and 4 screws (E).

18. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

(a) Connect each connector.

(b) Engage the 4 claws and 2 guides to install the No. 2 instrument panel under cover sub-assembly.





19. INSTALL FRONT DOOR SCUFF PLATE RH

20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

21. INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

(a) Engage the 6 claws to install the No. 4 instrument panel register assembly.

22. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

(a) Engage the 4 clips to install the No. 2 instrument cluster finish panel garnish.

23. INSTALL INSTRUMENT SIDE PANEL LH

(a) Engage the 4 claws and 3 guides to install the instrument side panel LH.

24. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation (from 12/2010)

25. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH

(a) Connect each connector.

(b) Engage the 7 claws and 4 clips.

(c) Engage the 2 claws to connect the room temperature sensor.

(d) Connect the hood lock control cable.

(e) Install the lower instrument panel finish panel LH with bolt (B) or (C) and screw (E).





(f) Close the cover as shown in the illustration.

26. INSTALL FRONT DOOR SCUFF PLATE LH

27. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

28. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

(a) Engage the 4 clips to install the No. 1 instrument panel register assembly.

29. INSTALL COMBINATION METER ASSEMBLY Installation (from 12/2010)

30. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

(a) Engage the 3 claws.

(b) Install the No. 2 instrument cluster finish panel subassembly with the 2 screws (E).

31. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY

(a) Connect each connector.

(b) Engage the 8 clips to install the instrument panel sub-assembly.

32. INSTALL INSTRUMENT PANEL FINISH PLATE (w/o Smart Key System)

(a) Install the instrument panel finish plate.

33. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

(a) Engage the 2 clips to install the No. 1 instrument cluster finish panel garnish.





34. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

(a) Connect each connector.

(b) Engage the 9 claws and 2 clips to install the center instrument cluster finish panel sub-assembly.

35. INSTALL INTEGRATION CONTROL AND PANEL WITH NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System) Installation (from 12/2010)

36. INSTALL INTEGRATION CONTROL AND PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Navigation System) Installation (from 12/2010)

37. INSTALL CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL

(a) Engage the 10 clips to install the center upper instrument cluster finish panel.





38. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY Installation (from 12/2010)

39. INSTALL UPPER STEERING COLUMN COVER Installation (from 12/2010)

40. INSTALL LOWER STEERING COLUMN COVER Installation (from 12/2010)

41. ADJUST SPIRAL CABLE

42. INSTALL STEERING WHEEL ASSEMBLY Installation (from 12/2010)

43. INSTALL STEERING PAD Installation (from 12/2010)

44. INSTALL LOWER NO. 2 STEERING WHEEL COVER Installation (from 12/2010)

45. INSTALL LOWER NO. 3 STEERING WHEEL COVER Installation (from 12/2010)

46. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

47. INSPECT STEERING PAD

On-Vehicle Inspection (from 12/2010)

48. INSPECT SRS WARNING LIGHT

Diagnosis System (from 12/2010)
pro multis Credits:Operation CHARM About Operation CHARM