Transmission, Removing
Transmission, Removing
Special tools, testers and auxiliary items required
• Engine Support Bridge (10-222 A)
• Bracket for Engine (10-222 A/1)
• Engine Support Adapter (10-222 A/3)
• Bracket with Spindle and Hook (10-222 A/10)
• Adapter (10-222 A/18)
• Transmission Support (3282)
• Pin (3282/29)
• Adjustment Plate (3282/33)
• Transmission Support Jig (3336) (for transporting the transmission)
• Torque Wrench (5-50 Nm) (V.A.G 1331)
• Torque Wrench (40-200 Nm) (V.A.G 1332)
• Engine-/Gearbox Jack (V.A.G 1383 A)
• Bracket (T10346)
• Engine Support Device (3300 A)
• Adapter (VW 771/40) from Slide Hammer-Complete Set (VW 771)
• Hose Clamps up to 25 mm Dia. (3094)
• Transmission Support Elements (determine when mounting the adjustment plate on the transmission support)
• Grease for Clutch Plate Splines (G 000 100)
• M6 x 20 Collar Bolt
• M6 x 80 Collar Bolt
• M10 x 20 Bolt
- First, check whether a coded radio is installed. If so, obtain the anti-theft code.
- Turn off the ignition and disconnect the battery ground cable.
Later in the procedure, the engine support bridge (10-222 A) is connected to the engine lifting eyes.
- Remove the engine cover if it is blocking the lifting eyes.
- Remove the air filter housing if it is located near the battery.
- Remove the battery and the battery tray.
- Remove the shift cable lock washer - 1 - from the transmission shift lever - 2 - and remove the cable from the pin - arrow -.
- Remove the cable retainer from the selector cable.
• To avoid damage to the selector cable, the cable retainer must be disconnected from the selector lever before removal.
- Pull the locking mechanism all the way forward in the - direction of arrow 1 - and then unlock it to the left in the - direction of arrow 2 -.
- Press the relay lever forward, in the - direction of arrow 3 -.
- The relay lever is removed together with the cable retainer later in the procedure.
- Remove the cable bracket bolts/nut - arrows - from the transmission, move it to the side and secure it.
with a Pipe between the Clutch Master and Slave Cylinders
- Clamp off the supply hose to the master cylinder using a hose clamp up to 25 mm dia. (3094).
with a Hose/Line Assembly between the Clutch Master and Slave Cylinders
- Clamp off the hose on the hose/line assembly - A - to the clutch slave cylinder using a hose clamp up to 25 mm dia. (3094).
Continuation for All
- Pull the clip - arrow - for the hose/line assembly or pipe out to the stop.
- Remove the hose/line assembly or pipe from the breather assembly/slave cylinder and seal it off.
Do not press the clutch pedal anymore.
- Remove the ground strap - 1 - from the top starter bolt.
- Disconnect the connector - 2 - from the backup lamp switch.
- Disconnect the connector and the wire from the starter.
- Remove the upper engine to transmission bolts - arrows -.
- Remove the upper bolt from the starter.
- Install the bracket (T10346) to the rear most hole of the three battery tray holes.
- Use a M6 x 80 collar bolt or one of the battery tray bolts for this.
- Remove the foam pieces on the upper edges of the left and right fenders.
- Disconnect any hoses and wires in the area of the lifting eyes on the engine.
- Install the engine support bridge (10-222 A) in front of the engine hood support.
- Use to following special tools:
• Bracket for engine (10-222 A/1)
• Engine support adapter (10-222 A/3)
• Adapter (10 - 222 A/18)
• Shackle (10-222 A/12)
• Bracket with spindle and hook (10 - 222 A/10)
- Position the bracket for engine (10 - 222 A /1) :
• On the upper longitudinal members
• Directly next to the plenum chamber cover
• Behind the bolts - arrows 1 and 2 -
The bracket for engine (10-222 A/1) may not be positioned on the fender bolting plates, otherwise these will get damaged.
Both upper longitudinal members have a different surface.
The bracket for engine (10-222 A/1) therefore does not stand with the contact surface facing up.
- Attach the spindles to the lifting eyes on the engine.
- Install the shackle (10-222 A/12) to the bracket (T10346).
- Pretension the engine and transmission assembly and engine support bridge via the spindles.
The left drive axle must be removed later in the procedure.
- With the vehicle still sitting on its wheels, loosen the left front drive axle bolt - arrow - a maximum of 90°, otherwise the wheel bearing will be damaged.
- Remove the noise insulation.
- Remove the lower part of the left front wheel housing liner..
- Remove the left front level control system sensor from the control arm, if equipped.
- Remove the bracket from the starter.
- Remove the starter.
- Release the charge air hose connections - arrows 1 and 2 -.
- Remove the fan shroud - arrow - and fans.
- Remove the front exhaust pipe from the turbocharger (- arrow -).
- Remove the pendulum support.
- Remove the coupling rod from the stabilizer bar and move it to the side.
- Remove the left drive axle.
- Remove the right drive axle heat shield bolts - arrows - and shield, if equipped.
- Remove the right drive axle from the transmission and tie it up.
- Remove the transmission mount - 2 - to transmission mount bracket bolts - arrows -.
- Lower the transmission by adjusting the spindles, which are attached to the engine, to approximately 60 mm - a -.
• When lowering the engine and transmission assembly, pay attention to the connections of the lines, hoses and radiator.
- Remove the transmission mount bracket - 1 - to transmission bolts - arrows -.
- Remove the relay lever with the cable retainer. Refer to => [ Plastic Relay Lever ] Plastic Relay Lever.
- Remove the transmission shift lever from the gear shift shaft.
- Remove the small flywheel cover plate bolt - arrow - and plate - A -, if equipped.
- Remove the lower engine to transmission bolts - 2 -.
• Loosen the engine to transmission bolt - 3 - and leave it in hand tight.
- Install the bracket (T10346) using a bolt - 1 - in the left threaded hole in the subframe.
- Install the bracket (T10346) in the same angled position as the engine.
Bolt - 1 - = M6 x 20 collar bolt
- Install the engine support device (3300 A) to the bracket (T10346).
- Push the engine forward using the spindle on the engine support device (3300 A). Note the following when doing this:
• The Air Conditioning (A/C) compressor - 2 - must not touch the refrigerant line - 1 - - arrow -.
• The generator must not touch the refrigerant line.
• The pressure pipe must not touch the radiator.
To remove the transmission, the adjustment plate (3282/33) must be installed on the transmission support (3282).
- Install the transmission support (3282) to the engine-/gearbox jack (V.A.G 1383 A).
- Align the arms of the transmission support so that they match up with the holes in the adjustment plate.
- Install the support elements - A - as illustrated on the adjustment plate.
- Install the pins (3282/29) in place on the adjustment plate - C -.
- Position the engine-/gearbox jack (V.A.G 1383 A) under the vehicle. The arrow symbol - B - on the adjustment plate points in the direction of travel.
- Align the adjustment plate so that it is parallel to the transmission.
- Install the adapter (VW 771/40) to the transmission housing threaded hole as shown in the illustration.
- Install the pin (3282/29) into the hole on the transmission for the pendulum support bolt.
- Secure the transmission to the transmission support (3282) using a bolt (MD) - A -.
The arm - B - must be flush with the guide on the transmission support (3282) - arrow -.
- Remove the engine to transmission bolt - arrow -.
- Remove the last engine to transmission bolt (- C - in graphic N34-10359).
- Separate the transmission from the engine (alignment sleeves).
The right flange shaft - 1 - must be guided over the cylinder block bolt flange - 2 -.
Guide the right flange shaft - 1 - past the flywheel and the opening - arrow - in the intermediate plate.
- Move the transmission in the area of the differential with the spindles on the transmission support (3282) into an angled position.
• The differential must face upward.
- Guide the transmission and the differential over the subframe - A - and swing it out.
- Move the transmission higher than the differential if necessary.
- Move the transmission further while paying attention to the longitudinal member - arrows -.
- Carefully lower the transmission.
• Pay attention to the lines when lowering the transmission.