P0705

P0705 TRANSMISSION RANGE SWITCH A





Description
- The transmission range switch is installed to upper part of transaxle case.
- The transmission range switch detects the selector lever position and sends a signal to the TCM.




CONSULT-III Reference Value









On Board Diagnosis Logic
- This is an OBD-II self-diagnostic item.
- Diagnostic trouble code "P0705" with CONSULT-III is detected when TCM dose not receive the correct voltage signal from the switch based on the gear position.




Possible Cause
- Harness or connectors
(The transmission range switch circuit is open or shorted.)
- Transmission range switch




DTC Confirmation Procedure

CAUTION:
Always drive vehicle at a safe speed.

NOTE:
If "DTC Confirmation Procedure" has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test.
After the repair, touch "ERASE" on "SELF-DIAG RESULTS" and then perform the following procedure to confirm the malfunction is eliminated.

WITH CONSULT-III
1. Turn ignition switch ON.
2. Select "DATA MONITOR" mode for "TRANSMISSION" with CONSULT-III.
3. Start engine.
4. Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.
VEHICLE SPEED: More than 10 km/h (6 MPH)
ENG SPEED: More than 450 rpm
ACC PEDAL OPEN: More than 1.0/8
5. If DTC is detected, go to SEE Diagnosis Procedure.

WITH GST
Follow the procedure "WITH CONSULT-III".




Wiring Diagram - CVT - TR/SW






TCM TERMINALS AND REFERENCE VALUES
CVT Trouble Diagnosis.




Diagnosis Procedure
1. CHECK TRANSMISSION RANGE SW SIGNALS
With CONSULT-III
1. Turn ignition switch ON.
2. Select "ECU INPUT SIGNALS" in "DATA MONITOR" mode for "TRANSMISSION" with CONSULT-III.
3. Read out "P", "R", "N", "D" and "L" position switches moving selector lever to each position.






Without CONSULT-III
1. Turn ignition switch ON.
2. Check voltage between TCM connector terminals and ground while moving selector lever through each position.






OK or NG
OK - GO TO 5.
NG - GO TO 2.
2.CHECK TRANSMISSION RANGE SWITCH
1. Turn ignition switch OFF.
2. Disconnect transmission range switch harness connector.





3. Check continuity between transmission range switch harness connector terminals.






OK or NG
OK - GO TO 4.
NG - GO TO 3.
3.CHECK CONTROL CABLE ADJUSTMENT
Check transmission range switch again with control cable disconnected from manual shaft of A/T assembly. Refer to test group 2.
OK or NG
OK - Adjust control cable. Shift Control System.
NG - Check transmission range switch (Refer to test group 1) again after adjusting transmission range switch ( Service and Repair).
- If OK, INSPECTION END
- If NG, repair or replace transmission range switch. Service and Repair.
4. DETECT MALFUNCTIONING ITEM
Check the following items.
- Harness for short or open between ignition switch and transmission range switch.
- Harness for short or open between transmission range switch and TCM.
- 10A fuse [No.14, located in the fuse block (J/B)].
- Ignition switch. Description and Operation.
OK or NG
OK - GO TO 5.
NG - Repair or replace damaged parts.
5.CHECK DTC
Perform SEE DTC Confirmation Procedure.
OK or NG
OK - INSPECTION END
NG - GO TO 6.
6.CHECK TCM
1. Check TCM input/output signals. CVT Trouble Diagnosis.
2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK - INSPECTION END
NG - 1. Repair or replace damaged parts.
2. Replace the transaxle assembly. Removal and Installation(MR20DE), Removal and Installation (QR25DE).




Component Inspection

TRANSMISSION RANGE SWITCH





1. Check continuity between transmission range switch harness connector terminals.










2. If NG, check again with control cable (2) disconnected from manual shaft of CVT assembly. Refer to step 1.
(1): Manual shaft
(A): Lock nut
3. If OK on step 2, adjust control cable (2). Shift Control System.
4. If NG on step 2, remove transmission range switch from CVT and check continuity of transmission range switch terminals. Refer to step 1.
5. If OK on step 4, adjust transmission range switch. CVT Shift Control System.
6. If NG on step 4, replace transmission range switch. Service and Repair.