Removal And Installation

INSTRUMENT PANEL ASSEMBLY


Removal and Installation


CAUTION:
- Disconnect the negative and positive battery terminals.
- Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
- Be careful not to scratch pad and other parts.

INSTRUMENT PANEL ASSEMBLY

Removal
1. Remove center console mat and remove screws (A).





- Arrow Indicates Front
2. Open center console lid, remove center console felt pad and remove the center console screws (A).





3. Pull parking brake control handle up engaging the parking brake, then remove the center console.
4. Remove instrument lower finisher screw, remove instrument lower finisher, disconnect diagnostic connector and hood release cable.
5. Remove the shifter knob. Refer to Selector Lever Knob Removal And Installation (CVT), Component Of Control Device And Cable (MT).
6. Remove the CVT or MT finisher.
7. Remove the controller and controller finisher, disconnect the controller finisher connectors.
8. Remove the cluster lid C upper mask (non SE-R models).





9. Remove the double meter (1) (SE-R models).
10. Remove cluster lid C (1).





a. Remove cluster lid C screws (A).
b. Pull out cluster lid C (1) to disconnect harness connector and remove cluster lid C (1).
11. Remove the instrument panel trim (RH).





12. Remove glove box lower finisher screws (A), remove glove box lower finisher (1).
13. Remove the glove box assembly.
a. Remove the two lower glove box assembly screws (A).
b. Open the glove box and remove the four upper glove box assembly screws (B).





14. Remove instrument lower covers (LH and RH).
15. Remove the instrument lower cover (center) screws and remove the instrument lower cover (center).
16. Remove the instrument upper cover screws, remove the instrument upper cover.





17. Remove steering lock escutcheon (1), remove steering column cover screws (A) and remove steering column cover upper and steering column cover lower (2).
18. Disengage the metal clips, and then remove cluster lid A.





19. Remove the combination meter screws (A), pull out the combination meter (1) to disconnect the connector, remove the combination meter (1).
20. Remove the front pillar garnish. Refer to Body Side Trim.
21. Remove the steering wheel. Refer to Component Tests and General Diagnostics.
22. Remove the headlamp control switch. Refer to Service and Repair.
23. Remove the wiper control switch. Refer to Service and Repair.





24. Remove the passenger air bag module bolt (A) from the steering member.
25. Remove the instrument panel lower RH screw (A).





26. Remove the instrument panel screw inside the combination meter opening.
27. Remove the instrument panel screw at the upper LH corner.
28. Remove the instrument panel lower LH screw.
29. Remove the front tweeters (LH and RH). Refer to Service and Repair.
30. Remove the upper instrument panel bolts located near the front tweeters (RH and LH).
31. Disconnect the audio antenna.
32. Remove the instrument panel assembly.

Installation
Installation is in the reverse order of removal.

CLUSTER LID C

Removal
1. Remove the shifter knob. Refer to Selector Lever Knob Removal And Installation (CVT), Component Of Control Device And Cable (MT).
2. Remove the CVT or MT finisher.
3. Remove the controller and controller finisher, disconnect the controller finisher connectors.
4. Remove the cluster lid C upper mask (non SE-R models).





5. Remove the double meter (1) (SE-R models).
6. Remove cluster lid C (1).





a. Remove cluster lid C screws (A).
b. Pull out cluster lid C (1) to disconnect harness connector and remove cluster lid C (1).

Installation
Installation is in the reverse order of removal.

COMBINATION METER

Removal
1. Remove steering lock escutcheon (1), remove steering column cover screws (A) and remove steering column cover upper and steering column cover lower (2).





2. Disengage the metal clips, and then remove cluster lid A.
3. Remove the combination meter screws (A), pull out the combination meter (1) to disconnect the connector, remove the combination meter (1).






Installation
Installation is in the reverse order of removal.

GLOVE BOX ASSEMBLY

Removal
1. Remove the shifter knob. Refer to Selector Lever Knob Removal And Installation (CVT), Component Of Control Device And Cable (MT).
2. Remove the CVT or MT finisher.
3. Remove the controller and controller finisher, disconnect the controller finisher connectors.
4. Remove the cluster lid C upper mask (non SE-R models).





5. Remove the double meter (1) (SE-R models).
6. Remove cluster lid C (1).





a. Remove cluster lid C screws (A).
b. Pull out cluster lid C (1) to disconnect harness connector and remove cluster lid C (1).
7. Remove the instrument panel trim (RH).





8. Remove glove box lower finisher screws (A), remove glove box lower finisher (1).
9. Remove the glove box assembly.
a. Remove the two lower glove box assembly screws (A).
b. Open the glove box and remove the four upper glove box assembly screws (B).






Installation
Installation is in the reverse order of removal.

INSTRUMENT LOWER FINISHER

Removal
Remove instrument lower finisher screw, remove instrument lower finisher, disconnect diagnostic connector and hood release cable.

Installation
Installation is in the reverse order of removal.

CENTER CONSOLE ASSEMBLY

Removal
1. Remove center console mat and remove screws (A).





- Arrow Indicates Front
2. Open center console lid, remove center console felt pad and remove the center console screws (A).





3. Pull parking brake control handle up engaging the parking brake, then remove the center console.

Installation
Installation is in the reverse order of removal.