Seat Cover With Seat Cushion For Multi-Contour Seat
Seat Cover with Seat Cushion for Multi-contour Seat
Special tools, testers and auxiliary items required
• Special hook (3370)
• Trim removal wedge (3409)
Removing
• Follow all safety precautions when working on pyrotechnic components. Refer to => [ Pyrotechnic, Electrical and Mechanical Restraint System Components, Safety Precautions and Testing Procedures ] Testing and Inspection.
• Before handling pyrotechnical components (for example, disconnecting the connector), the person handling them must "discharge static electricity". For example, by briefly touching the door striker pin.
- Remove the front seat. Refer to => [ Power Standard Seat/Sport Seat/Super Sport Seat ] Power Standard Seat/Sport Seat/Super Sport Seat.
- Attach front seat to the fixture for seat repair (VAS 6136). Refer to => [ Installing Front Seat on Fixture for Seat Repair VAS 6136 ] Installing Front Seat on Fixture For Seat Repair VAS 6136.
- Remove backrest. Refer to => [ Backrest ] Backrest.
Front passenger seat - country-specific with passenger occupant detection system for front passenger airbag deactivating:
Never disconnect the connector - 4 - from the passenger occupant detection system control module (J706).
- Disconnect the connector - 3 - from the control module.
- Remove the screw - 1 -.
- Disengage the control module - 2 - from the bracket - arrow - and free up the control module and wire.
Continuation for driver seat and front passenger seat:
- Remove front trim bracket, compressor and multi-contour seat control module. Refer to => [ Front Trim Bracket, Compressor and Multicontour Seat Control Module ] Front Trim Bracket, Compressor and Multicontour Seat Control Module.
- Detach rubber strap - 2 - and molding - 1 - at the front of the seat pan.
- Detach tab hooks - 1 to 4 - at the bottom of the seat pan.
- Detach molding - 5 - at the rear of the seat pan using the special hook (3370).
- Detach the molding - 3 - from the seat frame on the sill-side.
- Detach the molding - 1 - and - 2 - from the seat frame on the sill-side.
- Free up the electric wire for the heating element and remove the sill-side seat bolster padding.
- Lift the seat cover - 3 - on the tunnel side.
- Disengage the tab - 1 - on the seat frame on the tunnel side.
- Detach the molding - 2 - from the seat pan frame on the tunnel side.
- Free up the heating element connector and remove the tunnel-side seat bolster padding.
- Remove expanding rivet - 2 - from the upholstery wire - 1 -.
- Unclip the center of the upholstery wire from the lower seat frame - arrow C -.
- Push the front upholstery wire down - arrow A - and remove from the lower seat frame - arrow B -.
- Repeat on the opposite side.
- Disconnect the connector on the seat cushion and free up the wires.
- Lift the seat cover and rear seat cushion - 1 - carefully and disengage the rubber band - 3 - for the seat cover from the lower seat frame.
- Unclip the seat cover clamping strip - 2 - from the seat depth adjuster cover using a trim removal wedge (3409) - arrows -.
- Remove the seat cover and seat cushion.
Installation
• Follow all safety precautions when working on pyrotechnic components. Refer to => [ Pyrotechnic, Electrical and Mechanical Restraint System Components, Safety Precautions and Testing Procedures ] Testing and Inspection.
• Before handling pyrotechnical components (for example, connecting electrical connector), the person handling them must "discharge static electricity". For example, by briefly touching the door striker pin.
• Observe all measures when installing the front seat. Refer to => [ Power Standard Seat/Sport Seat/Super Sport Seat ] Power Standard Seat/Sport Seat/Super Sport Seat.
Install in reverse order of removal. Note the following:
Information for installation: for example tightening specifications, replacing body parts, refer to => [ Seat Cover and Seat Cushion for Multi-contour Seat Assembly Overview ] Seat Cover and Seat Cushion For Multi-Contour Seat Assembly Overview.