Faulty Signal
Faulty signal
Fault-tracing information
Fault-tracing information
Fault-tracing information
Caution! The male and female pins on the electronic throttle unit connectors are gold plated. Great care must be taken when measuring. Damage to the gold plating can result in operating difficulties.
Continue - cont
------------------------
cont - Checking components and wiring
-------------------------------------------------
Checking components and wiring
- Ignition off.
Check the throttle unit and engine control module (ECM) connectors. Check for contact resistance and oxidation.
Check the resistance values of the potentiometers in the throttle unit.
Check that the shutter in the throttle unit is not blocked or sticking. Clean as necessary.
Check the function of the integrated return spring in the throttle unit by carefully manually turning the throttle to wide open position and then carefully releasing the throttle. Check that the return spring returns the shutter to its resting position.
If the return spring does not return the shutter, the throttle unit is defective.
Remedy as necessary.
Other information:
- Checking wiring and terminals Checking Wiring And Terminals
- For resistance values, see Component specifications Specifications
- For information about signals on 5 cylinder engines, see Signal specification Signal Description / Specification
- For information about signals on 6 cylinder engines, see Signal specification Signal Description / Specification
- To access or replace the throttle unit, see Throttle body (electronic throttle module (ETM)), replacing Removal and Replacement
- To clean the throttle unit, see Throttle body (TB), cleaning Procedures
Continue - Adaptation of the throttle unit
-------------------------------------------------
Adaptation of the throttle unit
Hint: Faults which caused this diagnostic trouble code (DTC) may affect the adaptation values for the throttle unit. Carry out adaptation of the throttle unit to update the adaptation values.
Note! The ignition must be switched on for at least 30 seconds after the basic conditions are met in order for the adaptation to start. It takes approximately 10 seconds to run the adaptation.
- Ignition off
- Reinstall the components and connectors etc.
- Ignition on
- Read off the parameters.
Check that the following basic conditions for adaptation of the throttle unit are met.
1. Ignition on / engine off
2. Battery voltage above 10 V
3. Accelerator pedal (AP) unaffected
4. The car must be stationary (no vehicle speed signal)
5. Engine coolant temperature (ECT) between 5-100 °C
6. Intake air temperature (IAT) above 5 °C.
Remedy as necessary.
Check that the adaptation is correctly run after the "Adaptation of the throttle unit running" parameter changes status from "YES" to "NO". When all basic conditions are met, the adaptation must be completed after approximately 40 seconds. When the adaptation is completed correctly, the following information will be displayed:
- Adaptation of the throttle unit: OK
- Adaptation of the throttle unit running: NO.
Select "Continue" without switching off the ignition when the adaptation is OK.
Continue - Checking the fault status
-------------------------------------------------
Checking the fault status
- Ignition on
- Read off the diagnostic status and the fault status for diagnostic trouble code (DTC) ECM-9117.
Check that the fault status is "NO FAULT FOUND" when the diagnostic status is COMPLETED. If the fault status is "FAULT FOUND" when the diagnostic status is COMPLETED there is a fault.
Is the fault status "NO FAULT FOUND"?
Yes - Fault Found
No - Replacing the component
-------------------------------------------------
Replacing the component
- Ignition off.
Try a new throttle unit. See Throttle body (electronic throttle module (ETM)), replacing Removal and Replacement.
Continue - Verification
-------------------------------------------------
Verification
Verification
Verification
Hint: After carrying out the repair, check that the fault has been remedied.
- Ignition off
- Reinstall the connectors, components etc.
- Ignition on
- Read off the parameters.
Check that the following basic conditions for adaptation of the throttle unit are met.
1. Ignition on / engine off
2. Battery voltage above 10 V
3. Accelerator pedal (AP) unaffected
4. The car must be stationary (no vehicle speed signal)
5. Engine coolant temperature (ECT) between 5-100 °C
6. Intake air temperature (IAT) above 5 °C.
Remedy as necessary.
Check that the adaptation is correctly run after the "Adaptation of the throttle unit running" parameter changes status from "YES" to "NO". When all basic conditions are met, the adaptation must be completed after approximately 40 seconds. When the adaptation is completed correctly, the following information will be displayed:
- Adaptation of the throttle unit: OK
- Adaptation of the throttle unit running: NO.
Select "Continue" without switching off the ignition when the adaptation is OK.
Continue - continued
------------------------
Verification, continued
- Ignition on
- Read off the diagnostic status and the fault status for diagnostic trouble code (DTC) ECM-9117.
Check that the fault status is "NO FAULT FOUND" when the diagnostic status is COMPLETED. If the fault status is "FAULT FOUND" when the diagnostic status is COMPLETED there fault is still present.
Is the fault status "NO FAULT FOUND"?
Yes - VERIFIED
No - VERIFICATION FAILED
------------------------
VERIFIED - Fault Found
VERIFICATION FAILED - Fault-tracing information
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
Do you want to exit fault-tracing?
Yes - FAULT-TRACING FAILED
No - Attempt New Test
------------------------
FAULT-TRACING FAILED - FAULT-TRACING FAILED
Attempt New Test - Fault-tracing information
-------------------------------------------------