Front Passenger's Seat Occupied Sensor G128
Front Passenger's Seat Occupied Sensor G128
If Front Passenger's Seat Occupied Sensor (G128) is replaced, also the upholstery, front seat cushion must always be replaced!
Removing
- Mount the fixture for seat repair (VAS 6136) on the engine and transmission holder (VAS 6095).
- Remove the front seat. Refer to => [ Front Seat ] Front Seat
- Attach the seat to the fixture for seat repair (VAS 6136).
- Remove the front seat belt latch => [ Front Seat Belt Latches ] Front Seat Belt Latches
- Remove seat cap => [ Cover Cap ] Cover Cap
Electric seat
- Remove electric seat front end trim => [ Power Seat Front Side Trim ] Power Seat Front Side Trim
- Remove electric seat trim => [ Power Seat Trim ] Power Seat Trim
- Remove electric seat trim bracket => [ Power Seat Trim Bracket ] Power Seat Trim Bracket
Partially electric seat
- Remove partially electric seat trim => [ Partial Power Seat Trim ] Partial Power Seat Trim
- Remove bracket and actuating lever, trim of partially electric/height adjustable seat => [ Partial Power/Height-Adjustable Seat Trim Bracket and Operating Lever ] Partial Power/Height-Adjustable Seat Trim Bracket and Operating Lever
Height-adjustable seat
- Remove height-adjustable seat trim => [ Height-Adjustable Seat Trim ] Height-Adjustable Seat Trim
- Remove bracket and actuating lever, trim of partially electric/height adjustable seat => [ Partial Power/Height-Adjustable Seat Trim Bracket and Operating Lever ] Partial Power/Height-Adjustable Seat Trim Bracket and Operating Lever
Seat without height adjustment
- Remove trim of seat (without height adjuster) => [ Seat Trim, without Height Adjustment ] Seat Trim, without Height Adjustment
- Remove bracket, trim, seat (without height adjuster) => [ Seat Trim Bracket, without Height Adjustment ] Seat Trim Bracket, without Height Adjustment
Passenger Seat with Pass-Through
- Remove the front seat trim => [ Passenger Seat Trim, with Pass-Through ] Passenger Seat Trim, with Pass-Through.
- Remove bracket and actuating lever, trim of partially electric/height adjustable seat => [ Partial Power/Height-Adjustable Seat Trim Bracket and Operating Lever ] Partial Power/Height-Adjustable Seat Trim Bracket and Operating Lever
All seats
- Remove front seat backrest. Refer to => [ Left Front Seat Backrest ] Left Front Seat Backrest
- Cover and upholstery, front seat cushion, removing and installing => [ Front Seat Cushion Cover and Upholstery ] Front Seat Cushion Cover and Upholstery
• Removal of seat occupied sensor is described for "Trendline" and "Comfortline" equipment lines. Removal is performed accordingly for "Sportline" equipment line.
- On seats with a massage-/ventilation function, remove cover - 1 - and loosen seat occupied sensor - 2 - from upholstery - 3 -.
- On seats without massage-/ventilation function, loosen seat occupied sensor - 4 - from upholstery - 5 -.
Installing
"Trendline" and "Comfortline" equipment lines
- Position flat wire - 1 - of Front Passenger's Seat Occupied Sensor (G128) into corresponding recess in center of upholstery.
- Pull off adhesive strips - 2 - from Front Passenger's Seat Occupied Sensor (G128) - arrow A - on right side.
- Adhere right sensor strip - 3 - of Front Passenger's Seat Occupied Sensor (G128) on to upholstery.
- Pull off adhesive strips - 4 - from Front Passenger's Seat Occupied Sensor (G128) - arrow B - on left side.
- Adhere left sensor strip - 5 - of the front passenger seat occupant sensor (G128) to the upholstery.
• While adhering, make sure that sensor strips are aligned so that they run parallel to recess in upholstery.
- Position flat wire - 6 - of Front Passenger Seat Occupied Sensor (G128) into corresponding recess on left rear edge of upholstery.
- Pull off adhesive strip - 7 - from Front Passenger Seat Occupied Sensor (G128) - arrow C - and adhere flat wire on to upholstery in this area.
- Position Front Passenger Seat Occupied Sensor (G128) - 8 - and wiring harness - 9 - into corresponding recesses on rear edge of upholstery.
- On seats with a massage-/ventilation function, position cover - 1 - on upholstery, fleece - 2 - must be located on lower side of cover when doing this.
Sportline equipment line
- Position flat wire - 1 - of Front Passenger Seat Occupied Sensor (G128) into corresponding recess of upholstery.
- Slide flat wire forward in direction of travel until the two tabs - 2 - are located in corresponding recess of upholstery.
- Press flat wire - 3 - in rear area of tabs - 2 - into recess of upholstery.
- Pull off adhesive strip - 1 - from Front Passenger Seat Occupied Sensor (G128) - arrow A -.
- Adhere Front Passenger Seat Occupied Sensor (G128) on to upholstery in this area.
- Pull off adhesive strip - 2 - from Front Passenger Seat Occupied Sensor (G128) - arrow B -.
- Adhere Front Passenger Seat Occupied Sensor (G128) on to upholstery in this area.
- Position Front Passenger Seat Occupied Sensor (G128) - 3 - and wiring harness - 4 - into corresponding recesses on rear edge of upholstery.
