Installation

SUSPENSION: REAR SHOCK ABSORBER: INSTALLATION

INSTALLATION
HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
- A bolt without a torque specification is shown in the standard bolt chart Standard Bolt - Specified Torque For Standard Bolts.

1. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH





(a) Install the rear shock absorber on the vehicle by installing the 3 nuts on the suspension support side.
Torque: 64 Nm (653 kgf-cm, 47 ft-lbf)
NOTE: When installing the shock absorber, make sure the lower coil spring bottom tip is on the vehicle's front side.





(b) Temporarily install the rear shock absorber lower side with a new nut and washer to the axle carrier.






(c) Tighten the new lock nut.
Torque: 27 Nm (275 kgf-cm, 20 ft-lbf)
2. INSTALL REAR SHOCK ABSORBER CAP LH
(a) Install the cap with the 3 nuts to the shock absorber.
Torque: 14 Nm (143 kgf-cm, 10 ft-lbf)
3. CONNECT TOE CONTROL LINK SUB-ASSEMBLY LH Installation

4. CONNECT REAR UPPER NO. 2 CONTROL ARM ASSEMBLY LH Installation

5. CONNECT REAR UPPER NO. 1 CONTROL ARM ASSEMBLY LH Installation

6. STAKE REAR AXLE SHAFT LH NUT Installation

7. INSTALL LOAD SENSING VALVE SENSOR BRACKET Installation

8. INSTALL REAR SPEED SENSOR LH Removal

9. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY Installation

10. INSTALL ROOF SIDE GARNISH INNER LH
(a) Install the garnish for standard body Installation.
(b) Install the garnish for long body Installation.
11. INSTALL ROOF SIDE GARNISH INNER RH
HINT: Use the same procedures described for the LH side.

12. INSTALL REAR SEAT SIDE GARNISH LH
(a) Install the garnish for standard body Installation.
(b) Install the garnish for long body Installation.
13. INSTALL REAR SEAT SIDE GARNISH RH
HINT: Use the same procedures described for the LH side.

14. INSTALL REAR DOOR SCUFF PLATE LH
(a) Install the scuff plate for standard body Installation.
(b) Install the scuff plate for long body Installation.
15. INSTALL REAR DOOR SCUFF PLATE RH
HINT: Use the same procedures described for the LH side.

16. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type) Installation

17. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type) Installation

18. INSTALL REAR SEATBACK ASSEMBLY CENTER (for Power Seat) Installation

19. INSTALL REAR SEATBACK ASSEMBLY RH
(a) Install the rear seatback for power seat Installation.
(b) Install the rear seatback for ottoman Installation.
20. INSTALL REAR SEAT CONSOLE BOX ASSEMBLY (for Ottoman) Installation

21. INSTALL REAR SEATBACK ASSEMBLY LH
(a) Install the rear seatback for power seat Installation.
(b) Install the rear seatback for ottoman Installation.
22. INSTALL REAR SEAT CUSHION ASSEMBLY CENTER (for Power Seat) Installation

23. INSTALL REAR SEAT CUSHION ASSEMBLY RH
(a) Install the seat cushion for power seat Installation.
(b) Install the seat cushion for ottoman Installation.
24. INSTALL REAR SEAT CUSHION ASSEMBLY LH
(a) Install the seat cushion for power seat Installation.
(b) Install the seat cushion for ottoman Installation.
25. INSTALL REAR WHEEL HOUSE LH LINER
(a) Install the liner with the 3 screws, 11 nuts, 2 clips to the vehicle side.
26. INSTALL NO. 6 ROCKER PANEL MOULDING PROTECTOR Installation







27. STABILIZE SUSPENSION
(a) Install the rear tires.
Torque: 140 Nm (1428 kgf-cm, 104 ft-lbf)
(b) Lower the vehicle and bounce it up and down several times to stabilize the rear suspension.
(c) Remove the rear tires.
(d) Jack up the axle carrier with a wooden block between the jack and axle carrier. Apply a load to the rear suspension so that the rear drive shaft assembly becomes level.






28. TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH
(a) Tighten the nut on the axle carrier.
Torque: 80 Nm (816 kgf-cm, 59 ft-lbf)
29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
30. INSTALL COWL TOP VENTILATOR LOUVER RH Installation

31. PERFORM INITIALIZATION
(a) Perform initialization Repair Instruction - Initialization.
NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.

32. INSTALL REAR WHEEL
Torque: 140 Nm (1428 kgf-cm, 104 ft-lbf)
33. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(a) Inspect and adjust the rear wheel alignment Rear Wheel Alignment.
34. CHECK SPEED SENSOR SIGNAL
(a) Check the speed sensor signal Test Mode Procedure.
35. ADJUST HEADLIGHT ASSEMBLY
(a) Adjust the headlight Adjustments.
36. ADJUST OBJECT RECOGNITION CAMERA
(a) Adjust the object recognition camera Adjustments.