FREE REPAIR MANUALS & LABOR GUIDES 1982-2013 Vehicles
Courtesy of Operation CHARM: Car repair manuals for everyone.
Home >> Ford >> 2012 >> Taurus AWD V6-3.5L Turbo >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> B Code Charts >> B0082 >> B0082:13

B0082:13




Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS)

Pinpoint Test O: DTCs B0082:11, B0082:12, B0082:13 and B0082:1A

Refer to Wiring Diagram Set 46, Supplemental Restraint System for schematic and connector information. Diagrams By Number

Normal Operation

The Restraints Control Module (RCM) continuously monitors the passenger safety belt retractor and circuits for the following faults:

- Resistance out of range

- Unexpected voltage

- Short to ground

- Faulted passenger safety belt retractor

If a fault is detected, the RCM (Restraints Control Module) will store DTC B0082:11, B0082:12, B0082:13 or B0082:1A in memory and send a message to the Instrument Panel Cluster (IPC) module to illuminate the air bag warning indicator.

The RCM (Restraints Control Module) analyzes the deployment loop resistance and uses this measurement in combination with an age correction factor to determine if a fault exists. The value displayed in the PID is the deployment loop resistance as measured by the RCM (Restraints Control Module). If the value displayed is lower or higher than the desired range (refer to diagram below), the RCM (Restraints Control Module) can set a DTC. As the deployment loop resistance drifts farther outside the desired range, the chance for a DTC increases. The RCM (Restraints Control Module) fault trigger threshold may vary as the vehicle ages. Small variations in resistance can occur due to the effect of road vibrations on terminal fit and/or temperature changes. These variables can result in an intermittent fault. For this reason, the test will require the PID value to be within the desired range before the fault is considered repaired, regardless if the module is reporting an on-demand DTC at time of diagnosis. Following this direction will help make sure that minor changes in resistance do not create a repeat concern. This test will use a process of elimination to diagnose each part of the deployment loop circuit including:

- Wiring

- Connections

- Passenger safety belt retractor

- RCM (Restraints Control Module)










This pinpoint test is intended to diagnose the following:

- Wiring, terminals or connectors

- Passenger safety belt retractor pretensioner

- RCM (Restraints Control Module)

PINPOINT TEST O : DTCs B0082:11, B0082:12, B0082:13 AND B0082:1A

WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy(R) and cause serious personal injury or death.

WARNING: Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors. Failure to follow this instruction may result in the accidental deployment of the safety belt pretensioners, adaptive load limiting retractors, or safety belt inflators, which increases the risk of serious personal injury or death.

NOTICE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.

Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test. Inspection and Verification

NOTE: Supplemental Restraint System (SRS) components should only be disconnected or reconnected when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS (Supplemental Restraint System).

NOTE: Always make sure the correct SRS (Supplemental Restraint System) component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar.
Check the part number listed in the Ford Catalog Advantage(TM) or equivalent to make sure the correct component is being installed. If an incorrect SRS (Supplemental Restraint System) component is installed, DTCs may set.

NOTE: The SRS (Supplemental Restraint System) must be fully operational and free of faults before releasing the vehicle to the customer.

O1 RETRIEVE RCM (Restraints Control Module) DTCs

- Ignition ON.

- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).

Was DTC B0082:11, B0082:12, B0082:13 or B0082:1A retrieved on-demand during self-test?

Yes
This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.

For DTC B0082:13 or B0082:1A, GO to O2.

For DTC B0082:11, GO to O8.

For DTC B0082:12, GO to O10.

No
This is an intermittent fault when present as a Continuous Memory Diagnostic Trouble Code (CMDTC) only.

For DTC B0082:13 or B0082:1A, GO to O13.

For DTC B0082:11, GO to O14.

For DTC B0082:12, GO to O15.

O2 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL RESISTANCE (DEPLOY_26_R) PID

- Enter the following diagnostic mode on the scan tool: DataLogger- RCM (Restraints Control Module).
- DEPLOY_26_R PID


Does the PID value read between 1.7 and 2.78 ohms?

Yes
GO to O12.

No
GO to O3.

O3 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL RESISTANCE (DEPLOY_26_R) PID WHILE CARRYING OUT THE HARNESS TEST

- While monitoring the DEPLOY_26_R PID, carry out the harness test of the passenger safety belt retractor circuits and accessible connectors (including any in-line connectors), by wiggling connectors and flexing the wire harness frequently.

Does the PID value read between 1.7 and 2.78 ohms while carrying out the harness test?

Yes
DEPOWER the SRS (Supplemental Restraint System) and REPAIR the connector, terminals or wire harness as needed.

Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. GO to O17. Diagrams By Number

No
For PID value less than 1.7 ohms, GO to O4.

For PID value greater than 2.78 ohms, GO to O6.

O4 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (LOW RESISTANCE INDICATED)

NOTE: This pinpoint test step will attempt to change the fault reported by the RCM (Restraints Control Module) by inducing a different fault condition. If the fault reported changes, this indicates the RCM (Restraints Control Module) is functioning correctly and is not the source of the fault.

- Ignition OFF.

- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Disconnect: Passenger Safety Belt Retractor C3202.

- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Ignition ON.

- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).

- DIAGNOSTIC TIP: When viewing DTCs with the passenger safety belt retractor disconnected, an open circuit fault would normally be retrieved.

Did the on-demand DTC change from B0082:1A to B0082:13?

Yes
GO to O11.

No
GO to O5.

O5 CHECK FOR A SHORT BETWEEN PASSENGER SAFETY BELT RETRACTOR CIRCUITS

- Ignition OFF.

- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Disconnect: RCM (Restraints Control Module) C310A and C310B.

- Measure the resistance between passenger safety belt retractor C3202-1, circuit CR147 (GN/OG), harness side and C3202-2, circuit RR147 (YE/VT), harness side.





Is the resistance greater than 10,000 ohms?

Yes
GO to O12.

No
REPAIR circuits CR147 (GN/OG) and RR147 (YE/VT). GO to O17.

O6 CHECK THE PASSENGER SAFETY BELT RETRACTOR CIRCUITS FOR AN OPEN

- Ignition OFF.

- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Disconnect: Passenger Safety Belt Retractor C3202.

- Disconnect: RCM (Restraints Control Module) C310A and C310B.

- Measure the resistance between RCM (Restraints Control Module) C310B, and passenger safety belt retractor C3202, harness side using the following chart.









Are the resistances less than 0.5 ohm?

Yes
GO to O7.

No
REPAIR circuit CR147 (GN/OG) or RR147 (YE/VT). GO to O17.

O7 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (OPEN INDICATED)

NOTE: This pinpoint test step will attempt to change the fault reported by the RCM (Restraints Control Module) by inducing a different fault condition. If the fault reported changes, this indicates the RCM (Restraints Control Module) is functioning correctly and is not the source of the fault.

- Connect: RCM (Restraints Control Module) C310A and C310B.

- Connect a fused jumper wire between passenger safety belt retractor C3202-1, circuit CR147 (GN/OG), harness side and C3202-2, circuit RR147 (YE/VT), harness side.

- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Ignition ON.

- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).

- DIAGNOSTIC TIP: When viewing DTCs with the passenger safety belt retractor circuits shorted together, a low resistance fault would normally be retrieved.

Did the on-demand DTC change from B0082:13 to B0082:1A?

Yes
GO to O11.

No
GO to O12.

O8 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED)

NOTE: This pinpoint test step will attempt to change the fault reported by the RCM (Restraints Control Module) by inducing a different fault condition. If the fault reported changes, this indicates the RCM (Restraints Control Module) is functioning correctly and is not the source of the fault.

- Ignition OFF.

- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Disconnect: Passenger Safety Belt Retractor C3202.

- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Ignition ON.

- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).

- DIAGNOSTIC TIP: When viewing DTCs with the passenger safety belt retractor disconnected, an open circuit fault would normally be retrieved.

Did the on-demand DTC change from B0082:11 to B0082:13?

Yes
GO to O11.

No
GO to O9.

O9 CHECK THE PASSENGER SAFETY BELT RETRACTOR CIRCUITS FOR A SHORT TO GROUND

- Ignition OFF.

- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Disconnect: RCM (Restraints Control Module) C310A and C310B.

- Measure the resistance between passenger safety belt retractor:
- C3202-1, circuit CR147 (GN/OG), harness side and ground.

- C3202-2, circuit RR147 (YE/VT), harness side and ground.






Are the resistances greater than 10,000 ohms?

Yes
GO to O12.

No
REPAIR circuit CR147 (GN/OG) or RR147 (YE/VT). GO to O17.

O10 CHECK THE PASSENGER SAFETY BELT RETRACTOR CIRCUITS FOR A SHORT TO VOLTAGE

- Ignition OFF.

- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Disconnect: Passenger Safety Belt Retractor C3202.

- Disconnect: RCM (Restraints Control Module) C310A and C310B.

- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Ignition ON.

- Measure the voltage between passenger safety belt retractor:
- C3202-1, circuit CR147 (GN/OG), harness side and ground.

- C3202-2, circuit RR147 (YE/VT), harness side and ground.






Is voltage present on either circuit?

Yes
REPAIR circuit CR147 (GN/OG) or RR147 (YE/VT). GO to O17.

No
GO to O12.

O11 CONFIRM THE PASSENGER SAFETY BELT RETRACTOR FAULT

NOTE: Make sure all restraint system components and the RCM (Restraints Control Module) electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.

- Ignition OFF.

- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Prior to reconnecting any previously disconnected SRS (Supplemental Restraint System) component:
- inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.

- inspect wire harness for any damage, pinched, cut or pierced wires.

- inspect RCM (Restraints Control Module) C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation. Refer to Restraints Control Module (RCM) .

- repair any concerns found.
Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. Diagrams By Number

- If previously installed, remove the fused jumper wire from the passenger safety belt retractor.

- Connect: Passenger Safety Belt Retractor C3202.

- Connect: RCM (Restraints Control Module) C310A and C310B (if previously disconnected).

- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Ignition ON.

- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).

Was the original DTC retrieved on-demand during self-test?

Yes
INSTALL a new passenger safety belt retractor. GO to O17.

No
In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS (Supplemental Restraint System) components at this time. SRS (Supplemental Restraint System) components should only be installed when directed to do so in the pinpoint test.

For DTC B0082:13 or B0082:1A, GO to O13.

For DTC B0082:11, GO to O14.

For DTC B0082:12, GO to O15.

O12 CONFIRM THE RCM (Restraints Control Module) FAULT

NOTE: Make sure all restraint system components and the RCM (Restraints Control Module) electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.

- Ignition OFF.

- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Prior to reconnecting any previously disconnected SRS (Supplemental Restraint System) component:
- inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.

- inspect wire harness for any damage, pinched, cut or pierced wires.

- inspect RCM (Restraints Control Module) C310A and C310B CPA (Connector Position Assurance) lever/lock for correct operation. Refer to Restraints Control Module (RCM) .

- repair any concerns found.
Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. Diagrams By Number

- If previously installed, remove the fused jumper wire from the passenger safety belt retractor.

- Connect: All Previously Disconnected Restraint System Components.

- Connect: RCM (Restraints Control Module) C310A and C310B (if previously disconnected).

- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Ignition ON.

- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).

Was the original DTC retrieved on-demand during self-test?

Yes
INSTALL a new RCM (Restraints Control Module). REFER to Restraints Control Module (RCM) . GO to O17.

No
In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS (Supplemental Restraint System) components at this time. SRS (Supplemental Restraint System) components should only be installed when directed to do so in the pinpoint test.

For DTC B0082:13 or B0082:1A, GO to O13.

For DTC B0082:11, GO to O14.

For DTC B0082:12, GO to O15.

O13 CHECK THE PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL RESISTANCE (DEPLOY_26_R) PID FOR AN INTERMITTENT LOW RESISTANCE OR OPEN CIRCUIT FAULT

- Enter the following diagnostic mode on the scan tool: DataLogger- RCM (Restraints Control Module).
- DEPLOY_26_R PID


- Attempt to recreate the fault by wiggling connectors (including any in-line connectors) and flexing the wire harness frequently.

Does the PID value read between 1.7 and 2.78 ohms?

Yes
The fault is not present and cannot be recreated at this time. Do not install any new SRS (Supplemental Restraint System) components at this time. SRS (Supplemental Restraint System) components should only be installed when directed to do so in the pinpoint test. GO to O16.

No
DEPOWER the SRS (Supplemental Restraint System) and REPAIR as necessary.

Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. GO to O17. Diagrams By Number

O14 CHECK FOR AN INTERMITTENT PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL SHORT TO GROUND FAULT

- Attempt to recreate the fault by wiggling connectors (including any in-line connectors) and flexing the wire harness frequently.

- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).

Was DTC B0082:11 retrieved on-demand during self-test?

Yes
DEPOWER the SRS (Supplemental Restraint System) and REPAIR as necessary.

Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. GO to O17. Diagrams By Number

No
The fault is not present and cannot be recreated at this time. Do not install any new SRS (Supplemental Restraint System) components at this time. SRS (Supplemental Restraint System) components should only be installed when directed to do so in the pinpoint test. GO to O16.

O15 CHECK FOR AN INTERMITTENT PASSENGER SEATBELT LOAD LIMITER DEPLOYMENT CONTROL SHORT TO VOLTAGE FAULT

- Ignition OFF.

- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Disconnect: Passenger Safety Belt Retractor C3202.

- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Attempt to recreate the fault by wiggling connectors (including any in-line connectors) and flexing the wire harness frequently.

- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).

Was DTC B0082:12 retrieved on-demand during self-test?

Yes
DEPOWER the SRS (Supplemental Restraint System) and REPAIR as necessary.

Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. GO to O17. Diagrams By Number

No
The fault is not present and cannot be recreated at this time. Do not install any new SRS (Supplemental Restraint System) components at this time. SRS (Supplemental Restraint System) components should only be installed when directed to do so in the pinpoint test. GO to O16.

O16 CHECK THE HARNESS AND CONNECTORS

- Ignition OFF.

- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Disconnect the passenger safety belt retractor C3202:
- inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.

- inspect wire harness for any damage, pinched, cut or pierced wires.

- inspect RCM (Restraints Control Module) C310A and C310B CPA (Connector Position Assurance) lever/lock for correct operation. Refer to Restraints Control Module (RCM) .


Were any concerns found?

Yes
REPAIR as necessary.

Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. GO to O17. Diagrams By Number

No
The fault is not present and cannot be recreated at this time. Do not install any new SRS (Supplemental Restraint System) components at this time. SRS (Supplemental Restraint System) components should only be installed when directed to do so in the pinpoint test. GO to O17.

O17 CHECK FOR ADDITIONAL SRS (Supplemental Restraint System) DTCs

- Ignition OFF.

WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

- Reconnect all SRS (Supplemental Restraint System) components (if previously disconnected).

- If previously directed to depower the SRS (Supplemental Restraint System), repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.

- Ignition ON.

- Enter the following diagnostic mode on the scan tool: Self Test- Restraints.

NOTE: When selecting Restraints from the Self Test menu, DTCs will be retrieved from the RCM (Restraints Control Module) and OCSM (Occupant Classification System Module).


Are any RCM (Restraints Control Module) and/or OCSM (Occupant Classification System Module) DTCs retrieved on-demand during self-test?

Yes
Do not clear any DTCs until all DTCs have been resolved. GO to the DTC Charts for pinpoint test direction. Air Bag Systems/Seat Belt Systems

No
CLEAR all RCM (Restraints Control Module) and OCSM (Occupant Classification System Module) CMDTCs (Continuous Memory Diagnostic Trouble Codes). PROVE OUT the SRS (Supplemental Restraint System). Repair is complete. RETURN the vehicle to the customer.

pro multis Credits:Operation CHARM About Operation CHARM