Front Subframe: Service and Repair
Sub-frame front, replacing
Special tools:
999 5716 Reading off tool 999 5716 Reading off tool
999 7070 Mounting 999 7070 Mounting
999 5460 Lifting hook 999 5460 Lifting hook
999 5500 SOCKET UPPER NUT REAR SHOCK ABSORBER 999 5500 SOCKET UPPER NUT REAR SHOCK ABSORBER
999 7062 Separator 999 7062 Separator
999 7076 Lever 999 7076 Lever
999 5562 PROTECTIVE SOCKET 999 5562 PROTECTIVE SOCKET
Note! The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct.
Removal
Preparatory work
Remove the front wheels on both sides.
Installing the lifting tool
the lifting tool: 999 5716 Reading off tool 999 5716 Reading off tool and lifting hooks: 999 5460 Lifting hook 999 5460 Lifting hook. Lift up the engine slightly so that the engine pads are unloaded.
Removing the wing liner
Remove:
- the plastic nuts, x2
- the wing liner.
Remove the right engine pad. See: Engine support insulator, right, B6324S5 Engine Support Insulator, Right
Removing the protective plate
Remove the 6 screws.
Note! There is a guide sleeve on the upper mounting for the plate. This must be lifted slightly so that the panel can be slid forward.
Raise and move the protective plate forward. Remove the protective plate.
Removing the protective cover under the engine
Remove:
- the bolts, x6
- the protective cover under the engine.
Removing the gearbox bolts to the lower torque rod
Removing the lower bolt to the front engine pad
Remove the lower bolt to the engine pad.
Removing the anti-roll bar link from the anti-roll bar on both sides
Remove the anti-roll bar. See: Anti-roll bar link front, replacing Anti-Roll Bar Link Front, Replacing
Removing the drive shaft
Remove the bolt for the drive shaft. Use a screwdriver in the brake disc as counterhold. Tap the drive shaft into the hub slightly. Use a brass drift.
Removing the link arm from the wheel spindle on both sides
Remove the ball joint according to
Removing the steering gear from the subframe
Remove:
- the nuts, x4
- the bolt, x1.
Removing the subframe
Caution! Ensure that no pipes or cables are under load or are trapped when lowering the sub-frame.
Release:
- the 2 x heated oxygen sensor (HO2S) connectors from the rear edge of the subframe
- the heated oxygen sensor (HO2S) connector from the front edge of the subframe.
Remove the bolt to the ground cable bracket on the front edge of the subframe.
Position a lifting table under the subframe.
Remove:
- the bolts to the subframe's brackets at the rear edge
- the bolts to the subframe in the front and rear edge
- the subframe's brackets.
Release the heated oxygen sensor (HO2S) cables from the anti-roll bar.
Remove the lower coolant hose from the bracket on the subframe.
Lower the subframe carefully. Release the oil pipes to the steering gear from the clips on the subframe.
Remove the bolt to the bracket holding the pressure pipe to the steering gear on the subframe.
Transferring the components
Transfer the link arms on both sides.
Install:
- the 2 x front screws to the control arms. Tighten. See: Tightening torque [1][2]Specifications
- the rear screw to the control arms. Tighten. See Tightening torque [1][2]Specifications.
Transfer the anti-roll bar. Fit the bolts to the anti-roll bar, M10 x4.
Transfer the right-hand engine pad.
Fit the bolts to the engine pad, x2, in accordance with: Tightening torque, B6324S5 Tightening Torque.
Install a new lower torque rod with the nuts. See Tightening torque, B6324S5 Tightening Torque.
Install new pipe/hose holder. Transfer the bracket to the lower coolant hose. Install an M6 screw in the bracket.
Installation
Installing the subframe
Caution! Ensure that no pipes or cables are loaded or trapped when raising the sub-frame.
Raise the subframe.
Install:
- the oil pipes to the steering gear in the clips on the subframe
- the bolt, M6, to the bracket holding the pressure pipe to the steering gear on the subframe
- the lower coolant hose in the bracket on the sub-frame.
See instructions about adjustment according to: Subframe, adjusting Adjustments
Install the sub-frame's four screws together with the sub-frame's brackets and engine heater, if installed.
Use new screws. Lube the screws with oil.
Tighten according to: Tightening torque, B6324S5 Tightening Torque. First tighten the screws on the sub-frame's left side, then on the right.
Tighten the screws for the brackets M10.
Install the heated oxygen sensor's cables on the anti-roll bar.
Remove the lifting table.
Install:
- the 2 x heated oxygen sensor (HO2S) connectors on the rear edge of the subframe
- the heated oxygen sensor (HO2S) connector on the front edge of the subframe
- the M6 screw to the ground cable mounting on the front edge of the subframe.
Installing the steering gear on the subframe
Install:
- the nuts, M10 x4.
- the M10 screw.
Fitting the lower bolt to the front engine pad
Install the lower M10 screw for the engine pad.
Installing the gearbox bolts to the lower torque rod
Fit the bolts, x2. Tighten in accordance with: Tightening torque [1][2]Specifications.
Installing the exhaust pipes between front and rear catalytic converters
Note! To ensure that there is no exhaust leakage, see: Flanged joint, assembling Removal and Replacement.
Install:
- both exhaust pipes
- both exhaust pipes' nuts, M8.
Installing the link arm on both sides
Install:
- the link arm. Use: 999 7076 Lever 999 7076 Lever.
- the nut. Tighten. See Tightening torque [1][2]Specifications. Counterhold using a Torx wrench to prevent damaging the ball joint boot.
Installing the anti-roll bar link on both sides
Install:
- the anti-roll bar link
- the nut. Tighten according to: Tightening torque [1][2]Specifications. Use socket 999 5500 SOCKET UPPER NUT REAR SHOCK ABSORBER 999 5500 SOCKET UPPER NUT REAR SHOCK ABSORBER and a Torx wrench as a counterhold to prevent damaging the rubber gaiter.
Installing the drive shaft
Fit the bolt on both sides in accordance with: Tightening torque Tightening Torque.
Use a screwdriver as counterhold.
Installing the protective cover under the engine
Install:
- the protective cover under the engine
- the bolts, M8 x6.
Installing the protective plate
Move the skid plate up into the bumper cover. Press forward until the mounting brackets enter the sub-frame. Install the screws.
Fitting the bolts to the right-hand engine pad
Fit the bolts, x2. Tighten in accordance with: Tightening torque, B6324S5 Tightening Torque.
Installing the wing liner
Install:
- the wing liner
- the plastic nuts, x2.
Removing the lifting tool
Remove the lifting tool 999 5716 Reading off tool 999 5716 Reading off tool , kit: 999 7070 Mounting 999 7070 Mounting and lifting hooks: 999 5460 Lifting hook 999 5460 Lifting hook.
Fitting the bolts to the torque rod
Install the 2 x M10 screws, by the suspension turret on both sides.
Finishing
Fit the front wheels on both sides in accordance with: Installing wheels Installing Wheels.
Remove the oil filler cap.
Install:
- the upper front engine casing
Note!
the oil filler cap. Carry out wheel alignment.
Note! If the entire subframe has been removed for exposing other units/components, do not perform wheel alignment after installing the subframe.