Center Console, Highline, Jetta from MY 10 and Golf Wagon from MY 10
Center Console, Highline, Jetta from MY 10 and Golf Wagon from MY 10
Removing
- Switch off the ignition.
Vehicles with automatic transmission
- Loosen boot from the cover.
Vehicles with manual transmission and Direct Shift Gearbox (DSG)
- Loosen boot from the cover.
All vehicles
- Remove parking brake lever trim.
- Remove the trim in the center of the instrument panel (Jetta from MY 10, Golf Wagon from MY 10). Refer to => [ Instrument Panel Center Trim, Jetta from MY 2010 and Golf Wagon from MY 2010 ] Instrument Panel Center Trim, Jetta from MY 2010 and Golf Wagon from MY 2010.
- Remove the trim around the heating and A/C controls (Jetta from MY 10, Golf Wagon from MY 10). Refer to => [ Heating and A/C Control Trim, Jetta from MY 2010 and Golf Wagon from MY 2010 ] Heating and A/C Control Trim, Jetta from MY 2010 and Golf Wagon from MY 2010.
- Remove the center cover (Jetta from MY 10, Golf Wagon from MY 10). Refer to => [ Center Cover, Jetta from MY 2010 and Golf Wagon from MY 2010 ] Center Cover, Jetta from MY 2010 and Golf Wagon from MY 2010.
Vehicles without CD changer
- Remove lining mat - 1 - from storage compartment.
- Remove the "AUX IN socket" - 2 -.
- Remove the cover - 4 - from the mounts in storage compartment.
- Remove the bolt - 3 - (1.5 Nm).
Vehicles with CD changer.
- Remove the CD changer - 1 -.
- Remove lining mat - 2 - from storage compartment.
- Remove the bolt - 3 - (1.5 Nm).
Vehicles with converter with socket
• There are condensers in the converter with socket, 12 V-230 V (U13) / converter with socket, 12 V-115 V (U27) housing that can be charged with a residual voltage.
• There is a danger of being electrocuted.
• In no case may the housing for the converter with socket, 12 V-230 V (U13) / converter with socket, 12 V-115 V (U27) be opened.
• Turn off the ignition and all electrical equipment.
• Remove the key.
• Whenever removing and installing components that are visible (switches, cover, trim) where a pry tool ( trim removal wedge (VAS 3409) , screwdriver) is going to be used, cover the area around the component with tape.
• No repairs may be performed on the connector, on the wires and on the 230 V socket.
• The entire unit must be replaced if ever there is a malfunction in the connector, in the wires and in the 230 V socket or in the converter.
- Open the cover - 1 -.
- Remove the socket cover - 2 - (clipped on both sides of the socket) using a trim removal wedge (VAS 3409).
- Remove the two bolts - 3 -.
- Remove the inner socket - 4 -. To do this, both of the side brackets - 5 - must be loosened.
- Release and disconnect the connector - arrow -.
- Release the socket - 4 - at the tabs - arrows - and then remove the socket.
- Remove the screws - 2 and 3 - (1.5 Nm).
- Remove the converter - 1 -.
Vehicles with cupholder
- Open beverage holder - 1 - and remove two bolts - 2 - (1.5 Nm).
- Pull cup holder out of center console.
• When installing, beverage holder must be inserted (first at bottom) into center console while in a closed state. Then it must be opened and then install the two bolts - 2 -.
All vehicles
- Remove trim panel - 1 - from mounts in lower area - arrow -.
- Remove trim panel from mounts in center console in upper area.
- Remove the "AUX IN socket" - 1 -.
- Remove bolts - 2 - and - 3 - (1.5 Nm).
- Release extension - 4 - from mounts in lower area.
- If the vehicle has a manual transmission, remove the noise insulation and shift mechanism - 3 - in the center console.
- Remove the two bolts - 2 - (1.5 Nm).
- Remove the ashtray - 1 - from center console and (depending on vehicle equipment) disconnect the wiring harnesses.
• The vehicle may have a storage compartment in place of an ashtray - 1 -. Removing the storage compartment is identical to removing the ashtray.
- Remove the bolt - 1 - (1.5 Nm).
- Pull left footwell trim - 2 - out of mounts.
• Removal of right footwell trim is identical.
• Be sure to install the footwell trim panel - 2 - into the retainer - 3 - first.
- Remove lining mat - 4 - from storage compartment.
- Remove the bolt - 5 - (1.5 Nm).
- Remove the two bolts - 3 - (1.5 Nm).
- Remove the two bolts - 2 - (1.5 Nm).
- Remove the cover on the center console - 1 - - in direction of arrow -.
• Install the bolts in the following sequence: - 2 -, - 5 - and - 3 -.
- Remove center console - 1 - from vehicle.
• Make sure the center console - 1 - locks securely into the mounts in the instrument panel - arrows -.
- Remove bolts - 1 -, - 2 -, - 3 - and - 4 - (1.5 Nm).
- Remove center console trim carrier - 5 - from vehicle.
