Entry
Entry
• Familiarity with the function and operation is essential in the event of customer concerns. Refer to the Owner's Manual.
• The electronic anti-theft protection is equipped with a protection code number.
• When performing servicing or Fault Finding use the Vehicle diagnostic tester.
• After connecting the battery, check all the vehicle accessories (radio, the clock, Convenience Systems). Refer to and the Owner's Manual.
General Information
The "Entry" Sound System has the following features:
• Monochrome display
• FM tuner
• CD player
• UHV Low
• 4 speaker channels, 20 watts each
The CD player integrated inside the radio plays the following formats:
• Audio CD
• CD-R
• CD-RW
• MP3
It is not possible to play the following formats:
• 8 cm CDs
• Mix CDs (CDs containing files and audio files)
The antenna is located in rear window on Sedan models. Wagon models have a roof antenna.
Troubleshooting
The radio is equipped with OBD.
Use the Vehicle diagnostic tester under "Guided Fault Finding".
Electronic Anti-Theft Protection
The radio has an anti-theft protection, which operates with the instrument cluster. The radio code is stored internally inside the radio and inside the instrument cluster.
After disconnecting the power supply to the radio, it is ready for use and the radio code does not need to be entered again. The requirement is that the first activation of the anti-theft system follows and that the radio is reconnected in the same vehicle.
Notes Regarding Function
After first activation of the electronic anti-theft system, an internal radio code is stored in the radio and in the instrument cluster. Now, if the power supply to the radio should be cut off while doing other work (for example, removing the radio or the battery), the data will be exchanged between the radio and the instrument cluster when the power supply is connected again.
During this, the internal radio code is compared to the one in the instrument cluster. If the radio code is identical, the instrument cluster recognizes that the radio connected belongs to that vehicle and the radio can be used immediately. The radio code does not need to be entered again.
If the radio is replaced, then the radio code must be entered.
Deactivating electronic anti-theft system.
Then, after the S-contact is switched on via the ignition lock, the comparison between instrument cluster and radio is started automatically.
The comparison lasts approximately 5 seconds. The Vehicle diagnostic tester must be connected during this time.
When the power supply is disconnected, the radio is ready for use in this vehicle once the power supply is connected. The radio code does not need to be entered again.
The electronic anti-theft system is activated and locks the radio as soon as:
• The radio is installed in a different vehicle.
• The instrument cluster is replaced.
The radio has been locked by the anti-theft protection. After switching on the radio "SAFE" and "1000" will appear in the display.
Deactivate the electronic anti-theft protection to cancel the lock.
Electronic Anti-Theft System, Deactivating
Reactivating a locked radio is only possible by entering correct radio code number for anti-theft protection.
• The radio code for the anti-theft system is attached to the radio card next to the serial number. Refer to the Owner's Manual.
• For reasons of safety, do not leave the radio card in the vehicle. Get the radio code from the customer.
• If a radio is being replaced, then use the number code of the replacement radio.
• Inform the customer the radio code has been changed.
- Get the radio code.
- Switch on the radio.
The radio automatically displays "SAFE" and then "1000".
- Enter the radio code using the radio station buttons 1 through 4. Use the first radio station button to enter the first digit of the radio code. Use the second radio station button to enter the second digit.
- Press the arrow and hold it until the electronic anti-theft protection is activated. This is indicated by a short signal sound.
If the radio code has been entered correctly into radio, a radio frequency appears on the display.
It is possible to enter the radio code again if it was entered incorrectly. If radio code is entered incorrectly twice, then the radio will lock up for one hour. Leave the radio on and the key in the ignition lock. The process can be repeated again after an hour. Note: Always two attempts, after that the radio will lock up for one hour.