Output Shaft, 5th, 6th and Reverse Gears
Output Shaft, 5th, 6th and Reverse Gears
Special tools, testers and auxiliary items required
• Thrust Plate (VW 401)
• Thrust Plate (VW 402)
• Punch (VW 407)
• Punch (VW 408A)
• Thrust Disc (VW 412)
• Tube 60 mm Dia. (VW 415A)
• Holding Plate (VW 309)
• Transmission Support (VW 353)
• Thrust Pad Con. 8/65 (VW 433)
• Thrust Tube (VW 454)
• Support channels (VW 457)
• Holding Fixture (VW 801)
• Thrust Pad 16.5/28 mm Dia. (VW 431)
• Thrust Tube (VW 455)
• Thrust Pad (VW 510)
• Tube 42 mm Dia. (VW 516)
• Sleeve (VW 519)
• Thrust Pad (30-11)
• Thrust Piece (40-105)
• Sleeve (40-20)
• Thrust Plate (2050)
• Tube (3296)
• Tapered roller bearing puller (V.A.G 1582)
• Attachment to V.A.G 1582 (V.A.G 1582/4)
• Grip (V.A.G 1582/7)
• Kukko Extractor 46-58 mm (21/7)
• Kukko Separating Tool 22-115 mm (17/2)
• Kukko Support (22/2)
Removing the Inner Race/Tapered Roller Bearing on the Side of the Clutch Housing.
- Mount the (30-11) on the output shaft before removing the puller.
Installing the Inner Race/Tapered Roller Bearing on the Side of the Clutch Housing
Removing the Outer Race / Tapered Roller Bearing from the Clutch Housing
A Kukko Support , for example, (22/2)
B Kukko Extractor 46-58 mm , for example, (21/7)
• Check the washer for damage after removing it and replace if necessary.
Installing the Outer Race/Tapered Roller Bearing in the Clutch Housing
- Place the washer under the outer race.
- Support the clutch housing with the (40-20) directly under the bearing mount.
Remove the Inner Race/Tapered Roller Bearing on the Side of the Transmission Housing
Before installing the tapered roller bearing puller :
- Remove the inner race/tapered roller bearing locking ring on the side facing the transmission housing.
- Mount the (VW 431) and (40-105) on the output shaft.
Installing the Inner Race/Tapered Roller Bearing on the Side of the Transmission Housing
- Choose the correct locking ring. Refer to => [ Selecting the Locking Ring ] and install.
Selecting the Locking Ring
- Choose and install the thickest locking ring that will fit.
- Select the locking ring according to the table. For the correct part number, refer to the Parts Catalog
Available Locking Rings
Removing the Outer Race/Tapered Roller Bearing from the Transmission Housing
A Kukko Support , for example, (22/2)
B Kukko Extractor 46-58 mm , for example, (21/7)
Installing the Outer Race/Tapered Roller Bearing into the Transmission Housing.
- Support the transmission housing under the bearing mount using the (2050).
Disassembling the Output Shaft
• Remove the inner race/tapered roller bearing on the side of the transmission housing. Refer to => [ Remove the Inner Race/Tapered Roller
Bearing on the Side of the Transmission Housing ].
Removing the 5th and 6th Gear Synchronizer Hub/Locking Collar and the 6th Gear
- Remove the locking ring beforehand.
Removing the Sleeve - A - over the Reverse Gear
- Remove the locking ring beforehand.
Removing the Reverse Gear Synchronizer Hub
- Remove the locking ring beforehand.
A Kukko Separating Tool 22-115 mm , for example, (17/2)
Assemble the Output Shaft.
Installed Position: Reverse Gear Synchronizer Hub
The stop - arrow A - on the reverse gear locking collar faces the splines on the output shaft - arrow B -.
Installing the Reverse Gear Synchronizer Hub
- Install the locking ring.
- Mount the reverse gear locking collar on the reverse gear synchronizer hub.
- Install the reverse gear and the needle bearing.
Installing the Sleeve - A -
Installed position: The wide collar points toward reverse gear selector gear.
- Install the locking ring.
Checking 5th and 6th Gear Synchronizing Ring for Wear
- Press synchronizer ring onto taper of the gear and measure gap dimension - a - using a feeler gauge.
Disassembling and Assembling Locking Collar and Synchronizer Hub for 5th and 6th Gears
1. Spring
2. Locking piece
3. Locking collar
4. Synchronizer hub
- Slide the locking collar over the synchronizer hub.
The notches for the locking pieces on the synchronizer hub and locking collar must line up with each other.
Assembling Locking Collar/Synchronizer Hub for 5th and 6th Gears
The locking collar is pushed over the synchronizer hub.
- Install the locking pieces and springs offset by 120°. The angled end of the spring must engage into the hollow locking piece.
- Install the 6th gear with needle bearing.
- Install the 6th gear synchronizer ring.
Installing the locking Collar/Synchronizer Hub for 5th and 6th Gears
On some locking collars, there is a chamfer on the outer diameter.
Installed position: The chamfer on the outer diameter of the locking collar faces toward the 5th gear selector gear
- Turn the synchronizer ring so that the grooves line up with the locking pieces.
- Install the locking ring.
- Install the 5th gear synchronizer ring.
- Install 5th gear selector gear with needle bearing.
• Installing the inner race/tapered roller bearing on the side of the transmission housing. Refer to => [ Installing the Inner Race/Tapered Roller
Bearing on the Side of the Transmission Housing ].
• Selecting the locking ring for the inner race/tapered roller bearing. Refer to => [ Selecting the Locking Ring ].