Large and Small Trim, Adjusting
Pillar and Side Trims, Convertible
Large and Small Trim, Adjusting
Large and small trim borders may have different gap dimensions with respect to side trim borders.
- Gap dimensions - A -, - B -, - C -, - D - should be between 3.5 and 4.5 mm to avoid jamming or damaging when opening or closing trims.
Adjusting gap dimension - A -.
Adjusting gap dimension - B -.
Adjusting gap dimension - C - and - D -.
Large and small trim may show different height with respect to side trim.
- Heights - A - and - B - should be same heights as side trim to avoid jamming or damage when opening or closing trim.
Adjusting trim height - A -.
Adjusting trim height - B -.
Adjusting gap dimension A
- Remove side trim. Refer to => [ Side Trim ] Pillar and Side Trims, Convertible.
- Disconnect pressure rod - 2 -.
- Open trim - 4 -.
- Loosen bolts - 1 -.
- Align trim module - 3 - in the - direction of the arrow -.
- Tighten bolts to - 1 - to 3 Nm.
- Close trim - 4 -.
- Connect pressure rod - 2 -.
- Check gap dimension - A - for a distance of 3.5-4.5 mm and repeat the adjustment if necessary.
- Install side trim. Refer to => [ Side Trim ] Pillar and Side Trims, Convertible.
Adjusting gap dimension B
- Remove side trim. Refer to => [ Side Trim ] Pillar and Side Trims, Convertible.
- Disconnect pressure rod - 2 -.
- Open trim - 4 -.
- Loosen bolts - 1 -.
- Align trim module - 3 - in the - direction of the arrow - using screwdriver - 5 -.
- Tighten bolts to - 1 - to 3 Nm.
- Close trim - 4 -.
- Connect pressure rod - 2 -.
- Check gap dimension - B - for a distance of 3.5-4.5 mm and repeat the adjustment if necessary.
- Install side trim. Refer to => [ Side Trim ] Pillar and Side Trims, Convertible.
Adjusting gap dimension C and D
- Remove side trim. Refer to => [ Side Trim ] Pillar and Side Trims, Convertible.
- Remove bolts - 1 -.
- Align trim module - 2 - in the - direction of the arrow -.
- Tighten bolts to - 1 - to 3 Nm.
- Check gap dimension - C - and - D - for a distance of 3.5 to 4.5 mm and repeat the adjustment if necessary.
- Install side trim. Refer to => [ Side Trim ] Pillar and Side Trims, Convertible.
Adjusting trim height A
- Remove side trim. Refer to => [ Side Trim ] Pillar and Side Trims, Convertible.
- Disconnect pressure rod - 1 - from lever - 4 -.
- Remove screw - 2 -.
- Rotate ball socket - 3 -.
The length of the pressure rod is changed by turning ball socket - 3 - on the pressure rod. As a result, the height of the trim is changed.
- Tighten nut - 2 -.
- Connect pressure rod - 1 - to lever - 4 -.
- Check trim height - A - and readjust if necessary.
- Install side trim. Refer to => [ Side Trim ] Pillar and Side Trims, Convertible.
Adjusting trim height B
- Remove side trim. Refer to => [ Side Trim ] Pillar and Side Trims, Convertible.
- Remove the main frame of the lid module. Refer to => [ Small Trim Lid Module Assembly Overview ] and => [ Small Trim Lid Module Assembly Overview ]. Item 12 Small Trim Lid Module Assembly Overview
- Remove bolts - 1 -.
- The height and angle in areas - A -, - B - and - C - can be changed by screwing bolts - 1 -, - 2 - and - 3 - in or out.
1 = A
2 = B
3 = C
- Tighten bolts to - 1 - to 3 Nm.
- Install the main frame of the lid module. Refer to => [ Small Trim Lid Module Assembly Overview ] and => [ Small Trim Lid Module Assembly Overview ]. Item 12 Small Trim Lid Module Assembly Overview
- Check trim height - B - and readjust if necessary.
- Install side trim. Refer to => [ Side Trim ] Pillar and Side Trims, Convertible.