Assembly Overview

Assembly overview, 09G, 6 Spd. A/T





1. ATF control plug, 27 Nm
^ Checking ATF level and topping up

2. Oil seal
^ Always replace

3. Overflow pipe, 2 Nm
^ Remove to drain ATF
^ Checking ATF level and topping up

4. Oil pan
5. Bolt, 7 Nm
^ Tighten oil pan bolts in several stages and using alternating and diagonal sequence

6. Seal
^ Always replace

7. Magnet
^ Qty. 2, in webs of oil pan
^ Clean before installing

8. Bolt 8 Nm plus 1/4 turn (90°)
^ Qty. 12 of various lengths, used to secure valve body to transmission
^ Always replace bolts
^ Observe allocation

9. Bolt, 11 Nm
^ Qty. 3
^ For securing oil strainer to valve body

10. Oil strainer
11. Automatic transmission hydraulic pressure sensor 1 -G193-
^ From July 2004 no longer installed

12. Automatic transmission hydraulic pressure sensor 2 -G194-
^ From July 2004 no longer installed

13. Valve body
^ Identification of solenoid valves

14. Bolt, 7 Nm
15. Bolt, 6 Nm
16. Transmission input speed (RPM) sensor -G182-
17. Bolt, 7 Nm
18. Transmission output speed (RPM) sensor -G195-
19. Transmission housing
20. Breather cap
21. ATF cooler
22. Multi-function Transmission Range (TR) switch -F125-
23. Transmission fluid temperature sensor -G93-
24. Bolt, 6 Nm
25. Wiring harness with 8-pin connector
^ With O-ring on connector, always replace O-ring
^ With Transmission fluid temperature sensor -G93-
^ For Transmission input speed (RPM) sensor -G182-
^ For Transmission output speed (RPM) sensor -G195-
^ For Automatic transmission hydraulic pressure sensor 1 -G193- and Automatic transmission hydraulic pressure sensor 2.
^ G194- (only installed to 06.04)
^ Location of sensors

26. Oil seal
^ Always replace

27. ATF drain plug, 40 Nm
28. Selector lever
^ For gear selector rod

29. Washer
30. Nut, 10 Nm
^ Observe installation position of nuts

31. Large spring
32. Small spring
33. Damper piston
34. Wiring harness with 14-pin connector
^ With O-ring on connector, always replace O-ring
^ For solenoid valves
^ Location of solenoid valves and routing of wiring harnesses

35. Bolt, 6 Nm

Identification of solenoid valves





1. Wiring harness with 14-pin connector - arrow - for solenoid valves
2. Solenoid valve 1 -N88-
3. Solenoid valve 2 -N89-
4. Solenoid valve 4 -N91-
5. Solenoid valve 6 -N93-
6. Solenoid valve 5 -N92-
7. Automatic transmission pressure regulating valve 4 -N218-
8. Automatic transmission pressure regulating valve 6 -N371-
9. Automatic transmission pressure regulating valve 5 -N233-

Identification of sensors





1. Automatic transmission hydraulic pressure sensor 1 -G193-
^ From July 2004 no longer installed

2. Connection to Transmission input speed (RPM) sensor -G182-
3. Wiring on Transmission input speed (RPM) sensor -G182-
4. Automatic transmission hydraulic pressure sensor 2 -G194-
^ From July 2004 no longer installed

5. Wiring on Transmission output speed (RPM) sensor -G195-
6. Connection to Transmission output speed (RPM) sensor -G195-
7. Retainer from Transmission fluid temperature sensor -G93-
8. Transmission fluid temperature sensor -G93-
9. Wiring harness with 8-pin connector - arrow -