Trouble In Passenger Airbag ON/OFF Indicator

SUPPLEMENTAL RESTRAINT SYSTEM: OCCUPANT CLASSIFICATION SYSTEM: Trouble in Passenger Airbag ON/OFF Indicator
- Trouble in Passenger Airbag ON/OFF Indicator

DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then informs a passenger of the front passenger airbag assembly and front seat side airbag assembly condition (activated/not activated) by the passenger airbag ON/OFF indicator.

HINT
Approximately 6 seconds after the ignition switch is turned to the on (IG), the passenger airbag ON/OFF indicator will be ON/OFF depending on the conditions listed below.





INSPECTION PROCEDURE

PROCEDURE

1. CHECK SRS WARNING LIGHT

(a) Turn the ignition switch on (IG), and check the SRS warning light condition.

HINT
If this trouble occurs, the SRS warning light is off. If the light is on, a DTC is output. Troubleshoot for the output DTC.

OK:

After the primary check period, SRS warning light goes off.

HINT
The primary check period is approximately 6 seconds after the ignition switch is turned on (IG).

NG -- GO TO DTC CHART Airbag System (for TMC Made)
OK -- Continue to next step.

2. PERFORM ZERO POINT CALIBRATION

(a) Turn the ignition switch off.

(b) Connect Techstream to the DLC3.

(c) Turn the ignition switch on (IG).

(d) Using Techstream, perform "zero point calibration" Programming and Relearning.

OK:

"Zero Point Calibration is complete." is displayed.

NG -- RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
OK -- Continue to next step.

3. PERFORM SENSITIVITY CHECK

(a) Using Techstream, perform "sensitivity check" Programming and Relearning.

Standard value:

27 to 33 kg (59.52 to 72.75 lb)

OK -- END
NG -- Continue to next step.

4. RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT

(a) Turn the ignition switch off.

(b) Loosen the 4 installation bolts of the front seat assembly RH.

(c) Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

Torque : 37 Nm (377 kgf-cm, 27 ft-lbf)

NEXT -- Continue to next step.

5. PERFORM ZERO POINT CALIBRATION

(a) Connect Techstream to the DLC3.

(b) Turn the ignition switch on (IG).

(c) Using Techstream, perform "zero point calibration" Programming and Relearning.

OK:

"Zero Point Calibration is complete." is displayed.

NG -- CHECK CONNECTORS
OK -- Continue to next step.

6. PERFORM SENSITIVITY CHECK

(a) Using Techstream, perform "sensitivity check" Programming and Relearning.

Standard value:

27 to 33 kg (59.52 to 72.75 lb)

OK -- END
NG -- Continue to next step.

7. CHECK CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the negative (-) terminal cable from the battery.

(c) Check that the connectors are properly connected to the occupant classification ECU and the 4 occupant classification sensors.

OK:

The connectors are properly connected.

(d) Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.

(e) Check that the connectors are not damaged or deformed.

OK:

The connectors are normal.

NG -- REPAIR OR REPLACE CONNECTOR, THEN GO TO STEP 1
OK -- Continue to next step.

8. CHECK DTC

(a) Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.

(b) Connect the negative (-) terminal cable to the battery.

(c) Turn the ignition switch on (IG), and wait for at least 60 seconds.

(d) Clear the DTCs stored in the occupant classification ECU Reading and Clearing Diagnostic Trouble Codes.

(e) for TMC made:

Clear the DTCs stored in the center airbag sensor assembly Airbag System (for TMC Made).

(f) except TMC made:

Clear the DTCs stored in the center airbag sensor assembly Airbag System (except TMC Made).

(g) Turn the ignition switch off.

(h) Turn the ignition switch on (IG), and wait for at least 60 seconds.

(i) Check the DTCs Reading and Clearing Diagnostic Trouble Codes.

OK:

DTC is not output.

NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal
OK -- Continue to next step.

9. REPLACE OCCUPANT CLASSIFICATION ECU

(a) Turn the ignition switch off.

(b) Disconnect the negative (-) terminal cable from the battery.

(c) Replace the occupant classification ECU Removal.

NEXT -- Continue to next step.

10. PERFORM ZERO POINT CALIBRATION

(a) Connect the negative (-) terminal cable to the battery.

(b) Connect Techstream to the DLC3.

(c) Turn the ignition switch on (IG).

(d) Using Techstream, perform "zero point calibration" Programming and Relearning.

OK:

"Zero Point Calibration is complete." is displayed.

NEXT -- Continue to next step.

11. PERFORM SENSITIVITY CHECK

(a) Using Techstream, perform "sensitivity check" Programming and Relearning.

Standard value:

27 to 33 kg (59.52 to 72.75 lb)

NEXT -- END