Installation
SEAT BELT: REAR SEAT INNER BELT ASSEMBLY: INSTALLATION
1. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
(a) Check the degree of the tilt when the ELR begins to lock.
(1) Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt while gently pulling the belt.
NOTICE:
Do not disassemble the retractor.
(b) Align the claw with the seat belt positioning hole and install the rear seat inner with center belt assembly LH with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
(a) Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
(b) Engage the 4 clips and 5 claws and install the package tray trim panel assembly.
(c) Connect the connector.
3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (for Reclining Seat Type)
(a) Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
(b) Engage the 4 clips and 5 claws and install the package tray trim panel assembly.
(c) Connect the connector.
4. INSTALL REAR SEAT SHOULDER BELT HOLE COVER
(a) Engage the 4 claws and install the rear seat shoulder belt hole cover.
5. INSTALL REAR SEAT SHOULDER BELT COVER
(a) Engage the 4 claws and install the rear seat shoulder belt cover.
HINT
Use the same procedures for the RH side and the LH side.
6. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)
(a) Connect the floor end of the rear seat outer belt assembly with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTICE:
Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.
(b) Check if the ELR locks.
NOTICE:
The check should be performed with the outer belt assembly installed.
(1) With the belt assembly installed, check that the belt locks when it is pulled out quickly.
7. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)
(a) Connect the floor end of the rear seat outer belt assembly with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTICE:
Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.
(b) Check if the ELR locks.
NOTICE:
The check should be performed with the outer belt assembly installed.
(1) With the belt assembly installed, check that the belt locks when it is pulled out quickly.
8. INSTALL ROOF SIDE INNER GARNISH LH Installation
9. INSTALL ROOF SIDE INNER GARNISH RH Installation
10. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for TMC Made)
(a) Connect the floor end of the rear seat inner with center belt assembly LH with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTICE:
Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.
(b) Check if the ELR locks.
NOTICE:
The check should be performed with the outer belt assembly installed.
(1) With the belt assembly installed, check that the belt locks when it is pulled out quickly.
11. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for TMMK Made)
(a) Connect the floor end of the rear seat inner with center belt assembly LH with the nut.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTICE:
Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.
(b) Check if the ELR locks.
NOTICE:
The check should be performed with the outer belt assembly installed.
(1) With the belt assembly installed, check that the belt locks when it is pulled out quickly.
12. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (for TMC Made)
(a) Install the rear seat inner with center belt assembly RH with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTICE:
Do not allow the anchor part of the rear seat inner with center belt assembly RH to overlap the protruding parts of the floor panel.
13. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (for TMMK Made)
(a) Install the rear seat inner with center belt assembly RH with the nut.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTICE:
Do not allow the anchor part of the rear seat inner with center belt assembly RH to overlap the protruding parts of the floor panel.
14. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH Installation
15. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH
HINT
Use the same procedures for the RH side and the LH side.
16. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH (for Reclining Seat Type) Reassembly
17. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH (for Reclining Seat Type)
HINT
Use the same procedures for the RH side and the LH side.
18. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH Installation
19. INSTALL REAR DOOR SCUFF PLATE LH Installation
20. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH Installation
21. INSTALL REAR DOOR SCUFF PLATE RH Installation
22. INSTALL CENTER SEAT BACK ASSEMBLY (for Reclining Seat Type) Installation
23. INSTALL SEPARATE TYPE REAR SEAT BACK ASSEMBLY LH (for Reclining Seat Type) Installation
24. INSTALL SEPARATE TYPE REAR SEAT BACK ASSEMBLY RH (for Reclining Seat Type) Installation
25. INSTALL REAR SEAT BACK COVER (for Reclining Seat Type)
26. INSTALL REAR SIDE SEAT BACK ASSEMBLY LH (for Fold Down Seat Type) Installation
27. INSTALL REAR SIDE SEAT BACK ASSEMBLY RH (for Fold Down Seat Type)
HINT
Use the same procedures for the RH side and the LH side.
28. INSTALL SEPARATE TYPE REAR SEAT BACK ASSEMBLY LH (for Fold Down Seat Type) Installation
29. INSTALL SEPARATE TYPE REAR SEAT BACK ASSEMBLY RH (for Fold Down Seat Type) Installation
30. INSTALL REAR SEAT BACK ASSEMBLY (for Fixed Seat Type) Installation
31. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
32. INSTALL REAR SEAT HEADREST ASSEMBLY
33. INSTALL REAR SEAT CUSHION ASSEMBLY Installation