Installation

AUDIO / VISUAL: RADIO ANTENNA CORD: INSTALLATION

1. INSTALL SATELLITE RADIO ANTENNA ASSEMBLY (w/ Satellite Radio)

(a) Engage the 2 claws to install the satellite radio antenna assembly.





(b) Place the antenna cord in the cutout of the antenna nut.





(c) Install the satellite radio antenna assembly with the antenna nut.

Torque : 4.5 Nm (45 kgf-cm, 40 in-lbf)

(d) Connect the connector.





2. INSTALL ANTENNA CORD SUB-ASSEMBLY (w/ Satellite Radio)

HINT
The double-sided tape and tape are not available as supply parts. If these tapes still have enough adhesion to secure the roof headlining and antenna cord, reuse the tapes. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedure below.

(a) Apply new double-sided tape.





Text in Illustration





(1) Remove the double-sided tape from the roof headlining assembly.

(2) Peel off the appropriate amount of new double-sided tape.

HINT
Be careful not to touch the adhesive surface.





(3) Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

(4) Peel off the backing sheet from the double-sided tape.

(b) Install the antenna cord to the roof headlining assembly from the front of the vehicle.





Text in Illustration









Text in Illustration





HINT
Align the taped part of the antenna cable with the protrusion of the roof headlining, and apply tape to secure the cable to the headlining.

(c) Put the strips of the tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.

HINT
* If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.
* For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.
* For the rear corner of the roof headlining assembly, align the marking tape on the antenna cord with the rear edge of the roof headlining, and secure the antenna cord to the roof headlining assembly with tape.

3. INSTALL ANTENNA CORD SUB-ASSEMBLY (w/o Satellite Radio)

HINT
The double-sided tape and tape are not available as supply parts. If these tapes still have enough adhesion to secure the roof headlining and antenna cord, reuse the tapes. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedure below.

(a) Apply new double-sided tape.





Text in Illustration





(1) Remove the double-sided tape from the roof headlining assembly.

(2) Peel off the appropriate amount of new double-sided tape.

HINT
Be careful not to touch the adhesive surface.





(3) Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

(4) Peel off the backing sheet from the double-sided tape.

(b) Install the antenna cord to the roof headlining assembly from the front of the vehicle.





Text in Illustration





HINT
Align the taped part of the antenna cable with the protrusion of the roof headlining, and apply tape to secure the cable to the headlining.

(c) Put the strips of the tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.

HINT
* If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.
* For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.
* For the right rear corner of the roof headlining assembly, align the marking tape on the antenna cord with the rear edge of the roof headlining, and secure the antenna cord to the roof headlining assembly with tape.

4. INSTALL ROOF HEADLINING ASSEMBLY

HINT
Refer to the procedure from Install Roof Headlining Assembly Installation.

5. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

(a) Engage the 6 clamps and clip and install the No. 2 antenna cord sub-assembly.





6. INSTALL NO. 2 HEATER TO REGISTER DUCT (for TMC Made) Reassembly

7. INSTALL NO. 2 HEATER TO REGISTER DUCT (for TMMK Made) Reassembly

8. INSTALL NO. 3 HEATER TO REGISTER DUCT (for TMC Made) Reassembly

9. INSTALL NO. 3 HEATER TO REGISTER DUCT (for TMMK Made) Reassembly

10. INSTALL NO. 1 HEATER TO REGISTER DUCT (for TMC Made) Reassembly

11. INSTALL NO. 1 HEATER TO REGISTER DUCT (for TMMK Made) Reassembly

12. INSTALL DEFROSTER NOZZLE ASSEMBLY (for TMC Made) Reassembly

13. INSTALL DEFROSTER NOZZLE ASSEMBLY (for TMMK Made) Reassembly

14. INSTALL SIDE NO. 2 DEFROSTER NOZZLE DUCT (for TMC Made) Reassembly

15. INSTALL SIDE NO. 2 DEFROSTER NOZZLE DUCT (for TMMK Made) Reassembly

16. INSTALL SIDE NO. 1 DEFROSTER NOZZLE DUCT (for TMC Made) Reassembly

17. INSTALL SIDE NO. 1 DEFROSTER NOZZLE DUCT (for TMMK Made) Reassembly

18. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

HINT
Refer to the procedure from Install Instrument Panel Safety Pad Assembly Installation.