Door Ajar Indicator Malfunction
Door Ajar Indicator Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The door ajar and liftgate ajar switches supply a ground to the rear fuse block when the door is open. Once the door or liftgate is closed the door ajar switch opens removing the ground to the rear fuse block. The rear fuse block sends a signal to the instrument panel cluster (IPC) to illuminate the door ajar indicator when a door or liftgate is open.
Reference Information
Schematic Reference
* Door Lock/Indicator Schematics (Door Lock/Indicator Schematics)
* Release Systems Schematics (Release Systems Schematics)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Door Ajar Indicator Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, observe the scan tool Driver Door Status, Passenger Door Status, Rear Left Door Status and Rear Right Door Status parameters while opening and closing each door. The parameters should change from Door Closed to Door Open while opening and closing the doors.
• If the value does not change, refer to Door Ajar Malfunction.
2. Observe the Trunk Status parameter while opening and closing the liftgate. The parameter should change from Trunk Closed to Trunk Open while opening and closing the liftgate
• If the value does not change, refer to Liftgate Ajar Malfunction.
Circuit/System Testing
Door Ajar Malfunction
1. Ignition OFF, disconnect the harness connector at the appropriate door lock.
2. Test for less than 1 ohm between the ground circuit terminal listed below and ground:
* Driver door lock terminal 7
* Passenger door lock terminal 7
* Left rear door lock terminal 4
* Right rear door lock terminal 4
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool Driver Door Status, Passenger Door Status, Rear Left Door Status and Rear Right Door Status parameters are Door Closed.
• If not the specified value, test the signal circuit terminal listed below for a short to ground. If the circuit tests normal, replace the rear fuse block.
* Driver door lock terminal 6
* Passenger door lock terminal 6
* Left rear door lock terminal 5
* Right rear door lock terminal 5
4. Install a 3A fused jumper wire between the signal circuit terminal listed below and ground. Verify the scan tool Driver Door Status, Passenger Door Status, Rear Left Door Status and Rear Right Door Status parameters are Door Open.
* Driver door lock terminal 6
* Passenger door lock terminal 6
* Left rear door lock terminal 5
* Right rear door lock terminal 5
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the rear fuse block.
5. If all circuits test normal, test or replace the door lock.
Liftgate Ajar Malfunction
1. Ignition OFF, disconnect the harness connector at the liftgate latch assembly.
2. Ignition ON, verify the scan tool Trunk Status parameter is Trunk Closed.
• If not the specified value, test the signal circuit terminal 3 for a short to ground. If the circuit tests normal, replace the rear fuse block.
3. Install a 3A fused jumper wire between the signal circuit terminal 3 and the ground circuit terminal 2. Verify the scan tool Trunk Status parameter is Trunk Open.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the rear fuse block.
4. If all circuits test normal, test or replace the liftgate latch assembly.
Component Testing
Door Lock
1. Ignition OFF, disconnect the harness connector at the appropriate door lock.
2. Test for infinite resistance between the signal terminal and the ground terminal listed below with the door lock in the open position.
* Driver door lock signal terminal 6 and ground terminal 7
* Passenger door lock signal terminal 6 and ground terminal 7
* Left rear door lock signal terminal 5 and ground terminal 4
* Right rear door lock signal terminal 5 and ground terminal 4
• If not the specified value, replace the door lock.
3. Test for less than 2 ohms between the signal terminal and the ground terminal listed below with the door lock in the closed position.
* Driver door lock signal terminal 6 and ground terminal 7
* Passenger door lock signal terminal 6 and ground terminal 7
* Left rear door lock signal terminal 5 and ground terminal 4
* Right rear door lock signal terminal 5 and ground terminal 4
• If greater than the specified range, replace the door lock.
Liftgate Latch Assembly
1. Ignition OFF, disconnect the harness connector at the liftgate latch assembly.
2. Test for infinite resistance between the signal terminal 3 and the ground terminal 2 with the switch in the open position.
• If not the specified value, replace the liftgate latch assembly.
3. Test for less than 2 ohms between the signal terminal 3 and the ground terminal 2 with the switch in the closed position.
• If greater than the specified range, replace the liftgate latch assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Front Side Door Lock Replacement (Front Side Door Lock Replacement)
* Rear Door Lock Replacement (Rear Door Lock Replacement)
* Liftgate Latch Replacement (Sedan) (Service and Repair)Liftgate Latch Replacement (Coupe) (Service and Repair)
* Control Module References (Programming and Relearning) for rear fuse block replacement, setup, and programming