Removal And Installation

CONTROL LINKAGE

Removal and Installation


REMOVAL

1.Shift the shifter lever to the neutral position.
2.Remove air cleaner case. Removal And Installation.





3.Remove bracket (1), as per the following procedure.

White arrow indicates : Vehicle front

a.Disconnect clips (A) from bracket.
b.Remove bolts (B) from bracket.
c.Remove bracket.
4.Pull out and disconnect the each cable from the shifter lever A
and the selector lever, using a suitable remover.





5.While pressing the lock of the selector cable in the direction of the arrow shown in the figure, remove the selector cable from the cable mounting bracket.
6.While pressing the lock of the shifter cable in the direction of the arrow shown in the figure, remove the shifter cable from the cable mounting bracket.
7.Remove cable mounting bracket from transaxle case.
8.Pull the shifter lever knob upward to remove.
9.Remove center console assembly. Removal And Installation.
10.Pull out and disconnect the shifter cable from the pin of the M/T
shift selector assembly, using a suitable remover.





11.Pull up the stopper (A) of the selector cable in the direction of the arrow as shown in the figure.
12.Pull out and disconnect the selector cable from the pin of the M/
T shift selector assembly, using a suitable remover.





13.While pressing the lock of the selector cable in the direction of the arrow shown in the figure, remove the selector cable from the M/T shift selector assembly.
14.While pressing the lock of the shifter cable in the direction of the arrow shown in the figure, remove the shifter cable from the M/T
shift selector assembly.
15.Remove the M/T shift selector assembly.
16.Remove three way catalyst and heat plate. Removal And Installation.
17.Remove the bracket from the vehicle.





18.Disengage the pawls (A) of the grommet (1), and pull downwards to remove.
19.Remove the shifter cable and selector cable from the vehicle.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:
- Install each cable without causing interference with other parts, a 120 mm (4.72 in)-or-less bend, and a 180-degrees-or-more twist.
- Install boot of each cable without causing interference with other parts and a 90-degrees-or-more twist.
- Fit boot of to center console assembly the groove on shifter lever knob.
- To install the shifter lever knob, press it into the shifter lever.

CAUTION:
- Never reuse shifter lever knob.
- Be careful with orientation of shifter lever knob.
- Tapping work for tapping bolts is not applied to new transaxle case. Do not perform tapping by other than screwing tapping bolts because tapping is formed by screwing tapping bolts into transaxle case.

CAUTION:
Never reuse tapping bolt.
- Insert the each cable until it reaches the cable mounting bracket and M/T shift selector assembly.
- Insert the each cable until it reaches the shifter lever A and the selector lever.
- Shift the shifter lever to the neutral position.





- Install the shifter cable (1) and the selector cable (2) to the bracket (3) as shown in the figure.
Install the selector cable (the M/T shift selector assembly side), as per the following procedure.
1.Install the selector cable to the M/T shift selector assembly.
2.Shift the shifter lever to the neutral position.





3.Install the lever stopper (A) to the M/T shift selector assembly as shown in the figure.

CAUTION:
Selector cable cannot be adjusted accurately without using the lever stopper.
4.Check that the shifter lever does not move in the direction of the select. If it moves, repeat step 3.





5.Insert the stopper (A) until it reaches the selector cable.
6.Remove the lever stopper from the M/T shift selector assembly.
7.Shift the shifter lever to each gear position to check that there are no bindings. If any, repeat step 3.
1.Install the selector cable to the M/T shift selector assembly.
2.Shift the shifter lever to the 4th gear position.





3.Adjust the length "L" between the stopper (A) and the lever to the standard value.
Length "L": 3.51 - 4.11 mm (0.1382 - 0.1618 in)





4.Insert the stopper (A) until it reaches the selector cable.
5.Shift the shifter lever to each gear position to check that there are no bindings. If any, repeat step 3.