P1650
P1650 STARTER MOTOR RELAY 2
Description
ECM controls ON/OFF state of the starter relay, according to the engine and vehicle condition. Models with no
Intelligent Key System transmit a control signal directly to IPDM E/R. On the other hand, models with the Intelligent Key System transmit a control signal to IPDM E/R by way of BCM via CAN communication.
Under normal conditions, ECM controls and maintains the starter relay in OFF state during engine running or
"D" position.
When detecting a decrease in engine speed due to rapid deceleration or heavy load condition, ECM controls and reactivates the starter relay.
IPDM E/R detects a control state of starter relay and starter control relay and transmits a feedback signal to
ECM via CAN communication.
DTC Logic
DTC DETECTION LOGIC
NOTE:
- If DTC P1650 is displayed with DTC U1001, perform the trouble diagnosis for DTC U1001. U1001.
- If DTC P1650 is displayed with DTC P0607, perform the trouble diagnosis for DTC P0607. P0607.
- If DTC P1650 is displayed with B209F or B20A0 of IPDM E/R, perform the trouble diagnosis for B209F or
B20A0. B209F or B20A0.
- If DTC P1650 is displayed with B26F9 or B26FA of BCM, perform the trouble diagnosis for B209F or B20A0.
B26F9 or B26FA.
DTC CONFIRMATION PROCEDURE
1. PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.
- GO TO 2.
2. PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND C
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.
4.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to .
NO- GO TO 3.
3. PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
With CONSULT
CAUTION:
Always drive at a safe speed.
1.Start the engine.
2.Turn ignition switch OFF and wait at least 10 seconds.
3.Turn ignition switch ON.
4.Start the engine and warm it up to normal operating temperature.
5.Turn ignition switch OFF.
6.Lift up drive wheels.
7.Turn ignition switch ON.
8.Select "POWER BALANCE" in "ACTIVE TEST" mode of "ENGINE" using CONSULT.
9.Restart the engine and let it idle at least 10 seconds.
10.Shift the selector lever to D position while depressing fully the brake pedal.
11.Select 1 - 4 cylinders in "POWER BALANCE" and cut the fuel of all cylinders.
12.Check 1st trip DTC.
Without CONSULT
CAUTION:
Always drive at a safe speed.
1.Start the engine.
2.Turn ignition switch OFF and wait at least 10 seconds.
3.Turn ignition switch ON.
4.Start the engine and warm it up to normal operating temperature.
5.Turn ignition switch OFF.
6.Lift up drive wheels.
7.Restart the engine and let it idle at least 10 seconds.
8.Shift the selector lever to D position while depressing fully the brake pedal.
9.Remove vacuum hoses from intake manifold.
10.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to .
NO- INSPECTION END
Diagnosis Procedure
1. CHECK STARTER RELAY POWER SUPPLY CIRCUIT
Check the starter motor relay power supply circuit. IPDM E/R With I-Key (With Intelligent
Key system) or IPDM E/R Without I-Key (Without Intelligent Key system).
Is the inspection result normal?
YES- GO TO 2.
NO- Repair or replace error-detected parts.
2. CHECK STARTER RELAY CONTROL SIGNAL CIRCUIT
1.Turn ignition switch OFF.
2.Disconnect IPDM E/R harness connector.
3.Disconnect BCM harness connector.
4.Check the continuity between IPDM E/R harness connector and BCM harness connector.
5.Also check harness for short to ground to power.
1.Turn ignition switch OFF.
2.Disconnect IPDM E/R harness connector.
3.Disconnect ECM harness connector.
4.Check the continuity between IPDM E/R harness connector and ECM harness connector.
5.Also check harness for short to ground to power.
Is the inspection result normal?
YES- GO TO 3.
NO- Repair or replace error-detected parts.
3. CHECK INTERMITTENT INCIDENT
Perform Intermittent Incident.
Is the inspection result normal?
YES- Replace IPDM E/R. IPDM E/R (With I-Key).
NO- Repair or replace error-detected parts.