Removal And Installation Sedan

BODY SIDE TRIM

Removal and Installation


CAUTION:
- Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
- When removing, always use suitable tool made of plastic.
- When removing or installing body side welts, do not allow butyl seal to come in contact with pillar finishers.
- Make sure that clips are fully aligned with panel holes on body when installing, then press them in completely.

FRONT PILLAR FINISHER

Removal
1.Partially remove front body side welt.

CAUTION:
The front pillar finisher lower clip will not completely detach. Attempting to completely detaching it by force will damage the front pillar finisher.





2.Release the front pillar finisher (1) upper and lower clips by carefully prying inward while, using a suitable tool (A).
Broken Square indicates: Metal clip

CAUTION:
The lower clip will not completely release. Attempting to completely release by force may damage the finisher.
INT





3.Detach the front pillar finisher (1) lower clip (A) from the front pillar finisher (1), using a suitable tool (B).





4.Tilt the top of the front pillar finisher inward, and then pull out to remove from the vehicle.





5.Remove the front pillar finisher lower clip (A) from the front pillar by pinching, then tilting upward and removing from the front pillar.
Installation





1.Insert the front pillar finisher lower clip (A), onto the front pillar finisher (1) by sliding into the slot.





2.Position the front pillar finisher (1) at the bottom of the front pillar, then align the locator tabs into the tweeter speaker grille slot and the instrument panel slot.
Broken Square indicates: Metal clip





3.Align the front pillar finisher (1) lower clip (B) and upper clip (A) into their slots, then press into place, while installing the front pillar finisher (1).
INT
4.Install the front body side welt.

DASH SIDE LOWER FINISHER

Removal
1.Remove front kicking plate.
2.Release the clips, then remove dash side lower finisher.
Installation
Installation is in the reverse order of removal.

FRONT KICKING PLATE

Removal
Release the clip and pawls, then remove front kicking plate.
Installation
Installation is in the reverse order of removal.

FRONT BODY SIDE WELT

Removal
1.Remove front kicking plate.
2.Release welt from the body opening, then remove front body side welt.
Installation
Installation is in the reverse order of removal.

CENTER PILLAR LOWER FINISHER

Removal
1.Remove front and rear kicking plates.
2.Partially remove front and rear body side welts.
3.Release the clips and pawls, then remove center pillar lower finisher.
Installation
Installation is in the reverse order of removal.

REAR PILLAR FINISHER

Removal
1.Partially remove rear body side welt.
2.Remove screw cover, then remove the screw.
3.Release the clips, then remove rear pillar finisher.
Installation
Installation is in the reverse order of removal.

CENTER PILLAR UPPER FINISHER

Removal
1.Remove front and rear kicking plates.
2.Partially remove front and rear body side welts.
3.Remove screw cover, then remove the screw.
4.Remove front seat belt adjuster cover and shoulder anchor bolt. Removal And Installation.
5.Release clips and pawls, then remove center pillar lower finisher.
6.Release the clips, then remove center pillar upper finisher.
Installation
Installation is in the reverse order of removal.

REAR KICKING PLATE

Removal
Release the clip and pawl, then remove rear kicking plate.
Installation
Installation is in the reverse order of removal.

REAR BODY SIDE WELT

Removal
1.Remove rear kicking plate.
2.Release the welt from the body opening, then remove rear body side welt.
Installation
Installation is in the reverse order of removal.

SILL PLATE COVER (FRONT/REAR)

Removal
Release the pawls, then remove the sill plate cover.
Installation
Installation is in the reverse order of removal.