Engine Controls (Except For California)

DTC P2135 TP SENSOR





Component Description





Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc. The throttle position sensor responds to the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a kind of potentiometers which transform the throttle valve position into output voltage, and emit the voltage signal to the ECM. In addition, these sensors detect the opening and closing speed of the throttle valve and feed the voltage signals to the ECM. The ECM judges the current opening angle of the throttle valve from these signals and the
ECM controls the throttle control motor to make the throttle valve opening angle properly in response to driving condition.




CONSULT-III Reference Value in Data Monitor Mode
Specification data are reference values.









On Board Diagnosis Logic
This self-diagnosis has the one trip detection logic.

NOTE:
If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Engine Controls (Except For California) Engine Controls (Except For California).






FAIL-SAFE MODE
When the malfunction is detected, the ECM enters fail-safe mode and the MIL lights up.









DTC Confirmation Procedure

NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
1. Start engine and let it idle for 1 second.
2. Check DTC.
3. If DTC is detected, go to SEE Diagnosis Procedure.




Wiring Diagram





Specification data are reference values and are measured between each terminal and ground.

CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in damage to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.









Diagnosis Procedure
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.





2. Loosen and retighten ground screws on the body. Except For California.
- Arrow Indicates Vehicle Front
- Body ground (1)
OK or NG
OK - GO TO 2.
NG - Repair or replace ground connections.
2.CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT





1. Disconnect electric throttle control actuator (1) harness connector.
2. Turn ignition switch ON.





3. Check voltage between electric throttle control actuator terminal
2 and ground with CONSULT-III or tester.






OK or NG
OK - GO TO 3.
NG - Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness continuity between electric throttle control actuator terminal 4 and ECM terminal 36. Refer to Wiring Diagram.






4. Also check harness for short to ground and short to power.
OK or NG
OK - GO TO 4.
NG - Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK THROTTLE POSITION SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check harness continuity between the following;
Electric throttle control actuator terminal 1 and ECM terminal 33, Electric throttle control actuator terminal 3 and ECM terminal 34. Refer to Wiring Diagram.






2. Also check harness for short to ground and short to power.
OK or NG
OK - GO TO 5.
NG - Repair open circuit or short to ground or short to power in harness or connectors.
5.CHECK THROTTLE POSITION SENSOR
SEE Component Inspection.
OK or NG
OK - GO TO 7.
NG - GO TO 6.
6.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
Replace the electric throttle control actuator. Component.
- INSPECTION END
7.CHECK INTERMITTENT INCIDENT
Except For California Except For California.
- INSPECTION END




Component Inspection

THROTTLE POSITION SENSOR
1. Reconnect all harness connectors disconnected.
2. Perform Except For California.
3. Turn ignition switch ON.
4. Set shift lever to D position (CVT) or 1st position (M/T).





5. Check voltage between ECM terminals 33 (TP sensor 1 signal), 34 (TP sensor 2 signal) and ground under the following conditions.






6. If NG, replace electric throttle control actuator and go to the next step. Component.