P1777

P1777 STEP MOTOR





Description
- The step motor changes the step with turning 4 coils ON/OFF according to the signal from TCM. As a result, the flow of line pressure to primary pulley is changed and pulley ratio is controlled




CONSULT-III Reference Value









On Board Diagnosis Logic
- This is an OBD-II self-diagnostic item.
- Diagnostic trouble code "P1777" with CONSULT-III is detected under the following conditions.
- When operating step motor ON and OFF, there is no proper change in the voltage of TCM terminal which corresponds to it.




Possible Cause
- Step motor
- Harness or connectors
(Step motor circuit is open or shorted.)




DTC Confirmation Procedure

CAUTION:
Always drive vehicle at a safe speed.

NOTE:
If "DTC Confirmation Procedure" has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test.
After the repair, touch "ERASE" on "SELF-DIAG RESULTS" and then perform the following procedure to confirm the malfunction is eliminated.

WITH CONSULT-III
1. Turn ignition switch ON and select "DATA MONITOR" mode for "TRANSMISSION" with CONSULT-III.
2. Drive vehicle for at least 5 consecutive seconds.
3. If DTC is detected, go to SEE Diagnosis Procedure.

WITH GST
Follow the procedure "WITH CONSULT-III".




Wiring Diagram - CVT - STM






TCM TERMINALS AND REFERENCE VALUES
CVT Trouble Diagnosis.




Diagnosis Procedure
1.CHECK INPUT SIGNALS
With CONSULT-III
1. Start engine.
2. Select "SELECTION FROM MENU" in "DATA MONITOR" mode for "TRANSMISSION" with CONSULT-III.
3. Start vehicle and read out the value of "STM STEP", "SMCOIL A", "SMCOIL B", "SMCOIL C", and "SMCOIL D".






OK or NG
OK - GO TO 5.
NG - GO TO 2.
2.CHECK HARNESS BETWEEN TCM AND STEP MOTOR
1. Turn ignition switch OFF.
2. Disconnect CVT unit connector and TCM connector (A).





3. Check continuity between TCM connector (A) terminals and
CVT unit harness connector (B) terminals.






4. If OK, check harness for short to ground and short to power.
5. If OK, check continuity between body ground and CVT assembly.
6. Reinstall any part removed.
OK or NG
OK - GO TO 3.
NG - Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK STEP MOTOR
Check step motor. SEE Component Inspection.
OK or NG
OK - GO TO 5.
NG - GO TO 4.
4.CHECK DTC
With CONSULT-III
1. Turn ignition switch ON.
2. Perform "SELF-DIAG RESULTS" mode for "TRANSMISSION".
Is only "P1777" detected?
YES (Only DTC P1777 detected)-Replace control valve. Service and Repair.
YES (DTC P0725 and DTC U1000 in addition to DTC P1777 and detected)-When DTC is detected as listed below, replace control valve. Service and Repair.
- DTC for P1777 and P0725 are detected.
- DTC for P1777 and U1000 are detected.
- DTC for P1777, P0725 and U1000 are detected.
NO - Replace transaxle assembly. Removal and Installation(MR20DE), Removal and Installation (QR25DE).
5.CHECK TCM
1. Check TCM input/output signals. CVT Trouble Diagnosis.
2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK - INSPECTION END
NG - Repair or replace damaged parts.




Component Inspection

STEP MOTOR
1. Turn ignition switch OFF.
2. Disconnect CVT unit harness connector.





3. Check resistance between CVT unit harness connector terminals and ground.






4. If NG, perform "SELF-DIAG RESULTS" mode for "TRANSMISSION".