P0715

P0715 INPUT SPEED SENSOR A





Description
The primary speed sensor detects the primary pulley revolution speed and sends a signal to the TCM.




CONSULT-III Reference Value









On Board Diagnosis Logic
- This is an OBD-II self-diagnostic item.
- Diagnostic trouble code "P0715" with CONSULT-III is detected when TCM does not receive the proper signal from the sensor.




Possible Cause
- Harness or connectors
(Sensor circuit is open or shorted.)
- Primary speed sensor




DTC Confirmation Procedure

CAUTION:
Always drive vehicle at a safe speed.

NOTE:
If "DTC Confirmation Procedure" has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test.
After the repair, touch "ERASE" on "SELF-DIAG RESULTS" and then perform the following procedure to confirm the malfunction is eliminated.

WITH CONSULT-III
1. Turn ignition switch ON and select "DATA MONITOR" mode for "TRANSMISSION" with CONSULT-III.
2. Start engine and maintain the following conditions for at least 5 consecutive seconds.
VEHICLE SPEED: 10 km/h (6 MPH) or more
ACC PEDAL OPEN: More than 1.0/8
RANGE: "D" position
ENG SPEED: 450 rpm or more
Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving conditions required for this test.
3. If DTC is detected, go to SEE Diagnosis Procedure.

WITH GST
Follow the procedure "WITH CONSULT-III".




Wiring Diagram - CVT - PRSCVT






TCM TERMINALS AND REFERENCE VALUES
CVT Trouble Diagnosis.




Diagnosis Procedure
1.CHECK INPUT SIGNAL
With CONSULT-III
1. Start engine.
2. Select "ECU INPUT SIGNALS" in "DATA MONITOR" mode for "TRANSMISSION" with CONSULT-III.
3. Start vehicle and read out the value of "VSP SENSOR".






OK or NG
OK - GO TO 8.
NG - GO TO 2.
2.CHECK PRIMARY SPEED SENSOR
With CONSULT-III
1. Start engine.
2. Check power supply to primary speed sensor by voltage between TCM connector terminals 25, 46 and
48. CVT Trouble Diagnosis.






3. If OK, check the pulse when vehicle cruises.











OK or NG
OK - GO TO 8.
NG - GO TO 3.
3. CHECK POWER AND SENSOR GROUND
1. Turn ignition switch OFF.
2. Disconnect the primary speed sensor harness connector.
3. Turn ignition switch ON.





4. Check voltage between primary speed sensor harness connector terminals.










5. Check voltage between primary speed sensor harness connector terminal and ground.






6. If OK, check harness for short to ground and short to power.
7. Reinstall any part removed.
OK or NG
OK - GO TO 4.
NG - 1 - Battery voltage is not supplied between terminals 1 and
3, terminals 1 and ground: GO TO 6.
NG - 2 - Battery voltage is not supplied between terminals 1 and 3 only: GO TO 7.
4. CHECK HARNESS BETWEEN TCM AND PRIMARY SPEED SENSOR
1. Turn ignition switch OFF.
2. Disconnect TCM connector (A) and primary speed sensor harness connector (B).





3. Check continuity between TCM connector (A) terminal and primary speed sensor harness connector (B) terminal.






4. If OK, check harness for short to ground and short to power.
5. Reinstall any part removed.
OK or NG
OK - GO TO 5.
NG - Repair open circuit or short to ground or short to power in harness or connectors.
5. CHECK THE TCM SHORT
Replace same type TCM, perform self-diagnosis check. Erase self-diagnostic results and them drive the vehicle [more than 40 km/h (25 MPH)], perform self-diagnosis check. P0720.
Is "P0715 PRI SPEED SEN" detected again?
YES - Replace the Primary speed sensor. Primary Speed Sensor.
NO - Replace TCM. Service and Repair.
6. CHECK HARNESS BETWEEN TCM AND PRIMARY SPEED SENSOR (POWER)
1. Turn ignition switch OFF.
2. Disconnect TCM connector, IPDM E/R connector, primary speed sensor and secondary speed sensor harness connector.
3. Check continuity between TCM connector terminals, IPDM E/R harness connector terminal, primary speed sensor harness connector terminal and secondary speed sensor harness connector terminal. CVT Trouble Diagnosis.






4. If OK, check harness for short to ground and short to power.
5. Reinstall any part removed.
OK or NG
OK - 10 A fuse (No. 49, located in the IPDM E/R) or ignition switch are malfunctioning.
NG - Repair open circuit or short to ground or short to power in harness or connectors.
7. CHECK HARNESS BETWEEN TCM AND PRIMARY SPEED SENSOR (SENSOR GROUND)
1. Turn ignition switch OFF.
2. Disconnect TCM connector (A) and primary speed sensor harness connector (B).





3. Check continuity between TCM (A) connector terminal and primary speed sensor harness connector (B) terminal.






4. If OK, check harness for short to ground and short to power.
5. Reinstall any part removed.
OK or NG
OK - GO TO 8.
NG - Repair open circuit or short to ground or short to power in harness or connectors.
8.CHECK DTC
Perform P0720.
OK or NG
OK - INSPECTION END
NG - GO TO 9.
9.CHECK TCM
1. Check TCM input/output signals. CVT Trouble Diagnosis.
2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK - INSPECTION END
NG - Repair or replace damaged parts.