Front Seat Belt

FRONT SEAT BELT

SEAT BELT RETRACTOR : Removal and Installation


REMOVAL


WARNING:
Before servicing, push power switch OFF, disconnect 12V battery negative terminal and wait 5 minutes or more. Refer to "Precaution for Removing 12V Battery" Precaution for Removing 12V Battery.
Driver side
1.Remove shoulder anchor.
1.Slide driver seat to the frontmost position.





2.Pull adjuster cover in direction indicated by arrows as shown in the figure. Remove adjuster cover.

3.Remove shoulder anchor mounting anchor bolt.
2.Remove lap pre-tensioner.
1.Remove front kicking plate inner and rear kicking plate inner.
Refer to "KICKING PLATE INNER : Removal and Installation" Kicking Plate Inner.
2.Remove center pillar lower garnish.
Refer to "CENTER PILLAR LOWER GARNISH : Removal and Installation" Center Pillar Lower Garnish.
3.Remove driver seat from the vehicle.
Refer to "Removal and Installation" Removal and Installation.

CAUTION:
When removing and installing, use shop cloths to protect parts from damage.





4.Lift up lap pre-tensioner seat belt garnish, disengage pawls, and remove lap pre-tensioner seat belt garnish.

5.Pull up floor carpet.
6.Remove front floor spacer and rear floor spacer.
7.Disconnect lap pre-tensioner seat belt harness connector.

CAUTION:





- For installing/removing lap pre-tensioner connector, insert thin screwdriver wrapped in tape into notch, lift lock and remove connector.


- Install connector with lock raised, and push lock into connector.
- After installing the connector, check that the lock is pushed securely into it.





8.Remove joint bracket assembly LH mounting bolts (A).


9.Remove mounting anchor bolt of lap pre-tensioner, and then remove lap pre-tensioner from joint bracket assembly LH.
3.Remove seat belt pre-tensioner retractor.
1.Remove seat belt pre-tensioner retractor mounting anchor bolt and screw.
2.Disconnect seat belt pre-tensioner harness connector.

CAUTION:





- For installing/removing seat belt pre-tensioner connector, insert thin screwdriver wrapped in tape into notch, lift lock and remove connector.


- Install connector with lock raised, and push lock into connector.
- After installing the connector, check that the lock is pushed securely into it.
- Never place pre-tensioner seat belt in an area where the temperature reaches 80�C or more.
4.Remove seat belt adjuster.
1.Remove center pillar upper garnish.
Refer to "CENTER PILLAR UPPER GARNISH : Removal and Installation" Center Pillar Upper Garnish.
2.Remove seat belt adjuster mounting anchor bolts.
Passenger side
1.Remove shoulder anchor.
1.Slide passenger seat to the frontmost position.





2.Pull adjuster cover in direction indicated by arrows as shown in the figure. Remove adjuster cover.

3.Remove shoulder anchor mounting anchor bolt.
2.Remove outer anchor.
1.Remove front kicking plate inner and rear kicking plate inner.
Refer to "KICKING PLATE INNER : Removal and Installation" Kicking Plate Inner.
2.Remove center pillar lower garnish.
Refer to "CENTER PILLAR LOWER GARNISH : Removal and Installation" Center Pillar Lower Garnish.
3.Remove driver seat from the vehicle.
Refer to "Removal and Installation" Removal and Installation.

CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
4.Pull up floor carpet.
5.Remove front floor spacer and rear floor spacer.





6.Remove joint bracket assembly RH mounting bolts (A).

7.Remove mounting anchor bolt of outer anchor, and then remove outer anchor from joint bracket assembly RH.
3.Remove seat belt pre-tensioner retractor.
1.Disconnect seat belt pre-tensioner harness connector.

CAUTION:





- For installing/removing seat belt pre-tensioner connector, insert thin screwdriver wrapped in tape into notch, lift lock and remove connector.


- Install connector with lock raised, and push lock into connector.
- After installing the connector, check that the lock is pushed securely into it.
2.Remove seat belt pre-tensioner retractor mounting anchor bolt and screw.

CAUTION:
Never place pre-tensioner seat belt in an area where the temperature reaches 80�C or more.
4.Remove seat belt adjuster.
1.Remove center pillar upper garnish.
Refer to "CENTER PILLAR UPPER GARNISH : Removal and Installation" Center Pillar Upper Garnish.
2.Remove seat belt adjuster mounting anchor bolts.

INSTALLATION

Install in the reverse order of removal.