P0456

DTC P0456 EVAP CONTROL SYSTEM







On Board Diagnosis Logic
This diagnosis detects very small leaks in the EVAP line between fuel tank and EVAP canister purge volume control solenoid valve, using the intake manifold vacuum in the same way as conventional EVAP small leak diagnosis.

If ECM judges a leak which corresponds to a very small leak, the very small leak P0456 will be detected.
If ECM judges a leak equivalent to a small leak, EVAP small leak P0442 will be detected.
If ECM judges there are no leaks, the diagnosis will be OK.

CAUTION:
- Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the MIL may come on.
- If the fuel filler cap is not tightened properly,the MIL may come on.
- Use only a genuine NISSAN rubber tube as a replacement.

DTC Confirmation Procedure

CAUTION: Never remove fuel filler cap during the DTC confirmation procedure.

NOTE:
- If DTC P0456 or P1456 is displayed with P0442, first perform trouble diagnosis for DTC P0456 or P1456.
- After repair, make sure that the hoses and clips are installed properly.
- If "DTC CONFIRMATION PROCEDURE" has been previously conducted, always turn ignition switch "OFF" and wait at least 5 seconds before conducting the next test.

TESTING CONDITION:
- Open engine hood before conducting following procedure.
- If any of following condition is met just before the DTC confirmation procedure, leave the vehicle for more than 1 hour.
- Fuel filler cap is removed.
- Refilled or drained the fuel.
- EVAP component parts is/are removed.

- Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

WITH CONSULT-II
1. Turn ignition switch "ON" and select "DATA MONITOR" mode with CONSULT-II.
2. Make sure the following conditions are met.
FUEL LEVEL SE: 1.08 - 0.2 V
COOLAN TEMP/S: 0 - 35 °C (32 - 95 °F)
FUEL T/TMP SE: 0 - 32 °C (32 - 90 °F)
INT A/TEMP SE: More than 0 °C (32 °F)

If NG, turn ignition switch "OFF" and leave the vehicle in a cool place (soak the vehicle) or refilling/draining fuel until the output voltage condition of the "FUEL LEVEL SE" meets within the range above and leave the vehicle for more than 1 hour. Then start from step 1).

3. Turn ignition switch "OFF" and wait at least 5 seconds.
4. Turn ignition switch "ON".




5. Select "EVAP V/S LEAK P0456/P1456" of "EVAPORATIVE SYSTEM" in "DTC WORK SUPPORT" mode with CONSULT-II.
Follow the instruction displayed.
6. Make sure that "OK" is displayed.
If "NG" is displayed, refer to "Diagnostic Procedure" below.

NOTE:
- If the engine speed cannot be maintained within the range displayed on CONSULT-II screen, go to "Basic Inspection".
- Make sure that EVAP hoses are connected to EVAP canister purge volume control solenoid valve properly.

Overall Function Check

WITH GST
Use this procedure to check the overall function of the EVAP very small leak function. During this check, a DTC might not be confirmed.

CAUTION:
- Never use compressed air, doing so may damage the EVAP system.
- Do not start engine.
- Do not exceeded 4.12 kPa (0.042 kg/sq.cm , 0.6 psi).




1. Attach the EVAP service port adapter securely to the EVAP service port.
2. Set the pressure pump and a hose.
3. Also set a vacuum gauge via 3-way connector and a hose.
4. Turn ignition switch "ON".
5. Connect GST and select mode 8.
6. Using mode 8 control the EVAP canister vent control valve (close) and vacuum cut valve bypass valve (open).
7 .Apply pressure and make sure the following conditions are satisfied.
Pressure to be applied: 2.7 kPa (20 mmHg, 0.79 inHg)
Time to be waited after the pressure drawn in to the EVAP system and the pressure to be dropped: 60 seconds and the pressure should not be dropped more than 0.4 kPa (3 mmHg, 0.12 inHg)
If NG, go to "Diagnostic Procedure" below.

NOTE:
For more information, refer to GST instruction manual.

Diagnostic Procedure

Diagnostic Procedure Step 1 - 4:

Diagnostic Procedure Step 5 - 6:

Diagnostic Procedure Step 7 - 9:

Diagnostic Procedure Step 10 - 13:

Diagnostic Procedure Step 14 - 16:

Diagnostic Procedure Step 17:

Diagnostic Procedure Step 18 - 22:

Diagnostic Procedure Step 23: