Inspection Procedure 6
Inspection Procedure 6: The Multi Information Display Screen Cannot Be Changed With The Operation Of The Meter Information Meter Switch.CAUTION: Before replacing the combination meter, be sure to check that the power supply circuit, ground circuit, and communication circuit are normal.
Meter Information Switch Circuit:
TECHNICAL DESCRIPTION (COMMENT)
When the signal from the meter information switch is received, the combination meter switches the multi information display screen. If the multi information display screen does not switch normally, the meter information switch, wiring harness, connector(s), or combination meter may have a problem.
TROUBLESHOOTING HINTS
- The meter information meter switch may be defective
- The combination meter may be defective
- The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector
DIAGNOSIS
Required Special Tools:
- MB991223: Harness Set
- MB992006: Extra Fine Probe
- MB991958 Scan Tool (M.U.T.-III Sub Assembly)
- MB991824: Vehicles Communication Interface (V.C.I.)
- MB991827 M.U.T.-III USB Cable
- MB991910 M.U.T.-III Main Harness A (Vehicles with CAN communication system)
STEP 1. Using scan tool MB991958, read the combination meter diagnostic trouble code.
Check if DTC is set to the combination meter.
CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958. Refer to "How to connect the Scan Tool (M.U.T.-III) How to Connect the Scan Tool (M.U.T.-III)."
2. Turn the ignition switch to the "ON" position.
3. Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
4. Check if DTC is set.
Q: Is the DTC set?
YES : Troubleshoot the combination meter. Diagnostic Trouble Code Descriptions
NO : Go to Step 2.
STEP 2. Check meter information switch connector C-02 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Is meter information switch connector C-02 in good condition?
YES : Go to Step 3.
NO : Repair the connector.
STEP 3. Check the meter information meter switch.
Check the meter information meter switch. Meter Information Switch Check
Q: Is the check result normal?
YES : Go to Step 4.
NO : Replace the meter information meter switch.
STEP 4. Measure at meter information switch connector C-02 in order to the ground circuit to the meter information switch.
1. Disconnect meter information switch connector C-02, and measure at the wiring harness side.
2. Measure the resistance value between terminal 4 and ground.
- The measured value should be 2 ohms or less.
Q: Does the measured resistance value correspond with this range?
YES : Go to Step 6.
NO : Go to Step 5.
STEP 5. Check the wiring harness between meter information switch connector C-02 (terminal 4) and ground.
Check the ground wires for open circuit.
Q: Is the wiring harness between fuel meter information switch connector C-02 (terminal 4) and ground in good condition?
YES : Go to Step 6.
NO : Repair the wiring harness.
STEP 6. Check combination meter connector C-04 for loose, corroded or damaged terminals, or terminals pushed back in the connector.
Q: Is combination meter connector C-04 in good condition?
YES : Go to Step 7.
NO : Repair the connector.
STEP 7. Check the wiring harness between meter information switch connector C-02 (terminal 1) and combination meter connector C-04 (terminal 3).
Check the output lines for open circuit.
Q: Are the wiring harness between meter information switch connector C-02 (terminal 1) and combination meter connector C-04 (terminal 3) in good condition?
YES : Go to Step 8.
NO : Repair the wiring harness.
STEP 8. Retest the system.
Check that the multi information display screen switches normally when the meter information meter switch is operated.
Q: Is the check result normal?
YES : The trouble can be an intermittent malfunction.
NO : Replace the combination meter.