P0037
DTC P0037: Heated Oxygen Sensor (rear) Heater Circuit LowHeated Oxygen Sensor (Rear) Heater Circuit (Part 1):
Heated Oxygen Sensor (Rear) Heater Circuit (Part 2):
CIRCUIT OPERATION
- Power is supplied from the MFI relay (terminal No. 2) to the heated oxygen sensor (rear) heater.
- The ECM (terminal No. 35) controls continuity to the heated oxygen sensor (rear) heater by turning the power transistor in the ECM "ON" and "OFF".
TECHNICAL DESCRIPTION
- The ECM checks whether the heater current is within a specified range when the heater is energized.
- The ECM checks whether the heater voltage is within a specified range when the heater is not energized.
DESCRIPTIONS OF MONITOR METHODS
Heated oxygen sensor (rear) heater current or voltage is out of specified range.
MONITOR EXECUTION
Continuous
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
- Not applicable
Sensor (The sensor below is determined to be normal)
- Not applicable
DTC SET CONDITIONS
Logic Flow Chart
Logic Flow Chart:
Check Conditions
- More than 2 seconds have passed since the engine starting sequence was completed.
- While the heated oxygen sensor (rear) heater is on.
- Battery positive voltage is between 11 and 16.5 volts.
Judgement Criterion
- The heated oxygen sensor (rear) heater current has continued to be lower than 0.17 ampere for 2 seconds.
Check Conditions
- More than 2 seconds have passed since the engine starting sequence was completed.
- While the heated oxygen sensor (rear) heater is off.
- Battery positive voltage is between 11 and 16.5 volts.
Judgement Criterion
- The heated oxygen sensor (rear) heater voltage has continued to be lower than 2.0 volts for 2 seconds.
FAIL-SAFE AND BACKUP FUNCTION
- None
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 2. OBD- II Drive Cycle
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
- Open or shorted heated oxygen sensor (rear) heater circuit, or harness damage.
- Heated oxygen sensor (rear) heater failed.
- Connector damage.
- ECM failed.
DIAGNOSIS
Required Special Tools:
- MB991658: Test Harness
- MB992110: Power Plant ECU Check Harness
STEP 1. Check harness connector D-35 at the heated oxygen sensor (rear) for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 2.
NO : Repair or replace it. Then go to Step 12.
STEP 2. Check the heated oxygen sensor (rear).
1. Disconnect heated oxygen sensor (rear) connector D-35 and connect test harness special tool, MB991658, to the connector on the heated oxygen sensor (rear) side.
2. Measure the resistance between heated oxygen sensor connector terminal No. 1 and terminal No. 2.
Standard value: 4.5 - 8.0 Ohms [at 20°C (68°F)]
Q: Is the measured resistance between 4.5 and 8.0 Ohms [at 20°C (68°F)]?
YES : Go to Step 3.
NO : Replace the heated oxygen sensor (rear). Then go to Step 12.
STEP 3. Measure the power supply voltage at heated oxygen sensor (rear) harness side connector D-35.
1. Disconnect the connector D-35 and measure at the harness side.
2. Turn the ignition switch to the "ON" position.
3. Measure the voltage between terminal No. 1 and ground.
- Voltage should be battery positive voltage.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts) present?
YES : Go to Step 5.
NO : Go to Step 4.
STEP 4. Check harness connector A-34X at the MFI relay for damage.
Q: Is the harness connector in good condition?
YES : Check harness connectors C-43 and C-47 at intermediate connectors for damage, and repair or replace as required. Then go to Step 12.
NO : Repair or replace it. Then go to Step 12.
STEP 5. Measure the power supply voltage at ECM connector B-09 by using power plant ECU check harness special tool MB992110.
1. Disconnect all ECM connectors. Connect the power plant ECU check harness special tool MB992110 between the separated connectors.
2. Turn the ignition switch to the "ON" position.
3. Measure the voltage between terminal No. 35 and ground.
- Voltage should be battery positive voltage.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts) present?
YES : Go to Step 8.
NO : Go to Step 6.
STEP 6. Check harness connector B-09 at ECM for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Then go to Step 12.
STEP 7. Check for open circuit and short circuit to ground between heated oxygen sensor (rear) connector D-35 (terminal No. 2) and ECM connector B-09 (terminal No. 35).
NOTE: Check harness after checking intermediate connectors A-13 and C-45. If intermediate connectors are damaged, repair or replace them.
Q: Is the harness wire in good condition?
YES : Replace the ECM. When the ECM is replaced, register the ID code. Then go to Step 12.
NO : Repair it. Then go to Step 12.
STEP 8. Check harness connector B-09 at ECM for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Then go to Step 12.
STEP 9. Check for harness damage between MFI relay connector A-34X (terminal No. 2) and heated oxygen sensor (rear) connector D-35 (terminal No. 1).
NOTE: Check harness after checking intermediate connectors C-43 and C-47. If intermediate connectors are damaged, repair or replace them.
Q: Is the harness wire in good condition?
YES : Go to Step 10.
NO : Repair it. Then go to Step 12.
STEP 10. Check for harness damage between heated oxygen sensor (rear) connector D-35 (terminal No. 2) and ECM connector B-09 (terminal No. 35).
NOTE: Check harness after checking intermediate connectors A-13 and C-45. If intermediate connectors are damaged, repair or replace them. Then go to Step 12.
Q: Is the harness wire in good condition?
YES : Go to Step 11.
NO : Repair it. Then go to Step 12.
STEP 11. Check the trouble symptoms.
1. Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 2. OBD- II Drive Cycle
2. Check the diagnostic trouble code (DTC).
Q: Is DTC P0037 set?
YES : Replace the ECM. When the ECM is replaced, register the ID code. Then go to Step 12.
NO : It can be assumed that this malfunction is intermittent.
STEP 12. Test the OBD-II drive cycle.
1. Carry out a test drive with the drive cycle pattern. Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 2. OBD- II Drive Cycle
2. Check the diagnostic trouble code (DTC).
Q: Is DTC P0037 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.