C161E

DTC C161E: Electric Pump System





CAUTION:
^ If there is any problem in the CAN bus lines, an incorrect diagnostic trouble code may be set. Prior to this diagnosis, diagnose the CAN bus lines.
^ Whenever the ECU is replaced, ensure that the CAN bus lines are normal.

OPERATION
AWC-ECU controls the electric pump by the information from AWC pressure sensor and electric pump relay.

DTC SET CONDITIONS
The code is set when the electric pump operation signal is output from AWC-ECU, and when the AWC pressure sensor signal is not reached the specified pressure after the specified time has elapsed.

PROBABLE CAUSES
^ Fluid malfunction (low fluid level)
^ AWC pressure sensor malfunction
^ Electric pump relay malfunction
^ Hydraulic unit malfunction
^ Electric pump malfunction
^ Damaged harness wires and connectors
^ Malfunction of AWC-ECU

DIAGNOSTIC PROCEDURE

STEP 1. Scan tool CAN bus diagnostics
Using scan tool MB991958, diagnose the CAN bus lines.

Q: Is the check result normal?
YES: Go to Step 3.
NO: Repair the CAN bus lines. After repairing the CAN bus line, go to Step 2.

STEP 2. Check whether the DTC is reset.

Q: Is DTC No. C161E set?
YES: Go to Step 3.
NO: This diagnosis is complete.

STEP 3. Fluid check
Check that the fluid level is adequate.

Q: Is the check result normal?
YES: Go to Step 4.
NO: Add the fluid.

STEP 4. Scan tool diagnostic trouble code
Check if the ACD diagnostic trouble code No.C1611, C1612, C1625, or C161D is set.

Q: Is the DTC set?
YES: Perform the relevant troubleshooting.
NO: Go to Step 5.

STEP 5. Scan tool actuator test
OK: Operating sound of the electric pump can be heard.

Q: Is the check result normal?
YES: Go to Step 13.
NO: Go to Step 6.

STEP 6. Electric pump relay check.
Check the electric pump relay.

Q: Is the check result normal?
YES: Go to Step 7.
NO: Replace the electric pump relay. Then go to Step 14.

STEP 7. Electric pump relay connector check: A-22X

Q: Is the check result normal?
YES: Go to Step 8.
NO: Repair the defective connector. Then go to Step 14.

STEP 8. Check the wiring harness between A-22X electric pump relay connector terminal No.2 and fusible link (35).
Check the power supply line for short or open circuit.

Q: Is the check result normal?
YES: Go to Step 9.
NO: Repair the wiring harness. Then go to Step 14.

STEP 9. Electric pump connector check: F-29

Q: Is the check result normal?
YES: Go to Step 10.
NO: Repair the defective connector. Then go to Step 14.

STEP 10. Check the wiring harness between A-22X electric pump relay connector terminal No.4 and F-29 electric pump connector terminal No.2.
Check the power supply line for short or open circuit.

Q: Is the check result normal?
YES: Go to Step 11.
NO: Check C-136 and D-13 intermediate connectors. When no problem is found, repair the wiring harness. Then go to Step 14.

STEP 11. Check the wiring harness between F-29 electric pump connector terminal No.1 and body ground.
Check the ground line for open circuit.

Q: Is the check result normal?
YES: Go to Step 12.
NO: Repair the wiring harness. Then go to Step 14.

STEP 12. Check whether the DTC is reset.

Q: Is DTC No. C161E set?
YES: Replace the hydraulic unit. Then go to Step 13.
NO: Intermittent malfunction. (Refer to How to Cope with Intermittent Malfunction).

STEP 13. Check whether the DTC is reset.

Q: Is DTC No. C161E set?
YES: Replace the AWC-ECU. Then go to Step 14.
NO: This diagnosis is complete.

STEP 14. Check whether the DTC is reset.

Q: Is DTC No. C161E set?
YES: Return to Step 1.
NO: This diagnosis is complete.