FREE REPAIR MANUALS & LABOR GUIDES 1982-2013 Vehicles
Courtesy of Operation CHARM: Car repair manuals for everyone.
Home >> Mitsubishi >> 2008 >> Lancer Evolution L4-2.0L Turbo (4B11T/C) >> Repair and Diagnosis >> Lighting and Horns >> Hazard Warning Lamps >> Testing and Inspection >> Symptom Related Diagnostic Procedures >> Headlight >> Inspection Procedure 9

Inspection Procedure 9

Inspection Procedure 9: Any Of The Tail Lights, The Position Lights Or The License Plate Lights Does Not Illuminate.

Position Lights, Licence Plate Lights And Tail Lights Circuit (Part 1):




Position Lights,licence Plate Lights And Tail Lights Circuit (Part 2):






TECHNICAL DESCRIPTION (COMMENT)
If any of the tail lights, the position lights or the license plate lights does not Illuminate, the harness, connector(s), or bulb(s) may have a problem, or the fuse may be burned out.

TROUBLESHOOTING HINTS
- Malfunction of bulbs
- Malfunction of rear combination light
- Malfunction of rear combination light harness
- Malfunction of license plate light
- Malfunction of headlight
- Malfunction of tail light
- The wiring harness or connectors may have loose, corroded, or damaged terminals, or terminals pushed back in the connector

DIAGNOSIS

Required Special Tools:
- MB992006: Extra fine probe
- MB991223: Harness set

STEP 1. Rear combination light (taillight) check.

Q : Does the rear combination light (taillight) illuminate normally?

YES : Go to Step 2.

NO : Check the taillight (Refer to trouble symptom chart). Trouble Symptom Chart

STEP 2. Check headlight assembly connector A-40 (position light-LH) or A-57 (position light-RH), tail light connector F-24 (LH) or F-07 (RH) or license plate light connector F-18 (LH) or F-15 (RH) for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q : Is headlight assembly connector A-40 (position light-LH) or A-57 (position light-RH), tail light connector F-24 (LH) or F-07 (RH) or license plate light connector F-18 (LH) or F-15 (RH) in good condition?

YES : Go to Step 3.

NO : Repair or replace the damaged component(s). Refer to General (Electrical), Harness Connector Inspection.

STEP 3. Bulb check.

Check the bulb(s) of the light that does not illuminate.

Q : Is the check result normal?

YES : Go to Step 4.

NO : Replace the bulb(s) of the light that does not illuminate.

STEP 4. Resistance measurement at headlight assembly connector A-40 (position light-LH) or A-57 (position light-RH), tail light connector F-24 (LH) or F-07 (RH) or license plate light connector F-18 (LH) or F-15 (RH).

1. Disconnect the connector, and measure at the wiring harness side.
2. Measure the resistance between the connector of light which does not illuminate and the body ground.




- Measure the resistance between headlight assembly connector A-40 (LH) or A-57 (RH) (terminal 6) and body ground.




- Measure the resistance between tail light connector F-24 (LH) or F-07 (RH) (terminal 1) and body ground.




- Measure the resistance between license plate light connector F-18 (LH) or F-15 (RH) (terminal 1) and body ground.

OK: The measured value should be continuity exists (2 ohm or less).

Q : Does the measured resistance value correspond with this range?

YES : Go to Step 6.

NO : Go to Step 5.

STEP 5. Check the wiring harness between headlight assembly connector, tail light connector or license plate light connector and the body ground.

Check the ground line for open circuit.
- Check the wiring harness between headlight assembly (LH) connector A-40 (terminal 6) and the body ground. [position light-LH]
- Check the wiring harness between headlight assembly (RH) connector A-57 (terminal 6) and the body ground. [position light-RH]
- Check the wiring harness between tail light (LH) connector F-24 (terminal 1) and the body ground. [tail light-LH]

NOTE: Also check intermediate connector F-27 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector F-27 is damaged, repair or replace the connector as described in General (Electrical), Harness Connector Inspection.

- Check the wiring harness between tail light (RH) connector F-07 (terminal 1) and the body ground. [tail light-RH]

NOTE: Also check intermediate connector F-27 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector F-27 is damaged, repair or replace the connector as described in General (Electrical), Harness Connector Inspection.

- Check the wiring harness between license plate light (LH) connector F-18 (terminal 1) and the body ground. [license plate light-LH]
- Check the wiring harness between license plate light (RH) connector F-15 (terminal 1) and the body ground. [license plate light-RH]

Q : Is the wiring harness between headlight assembly connector, tail light connector or license plate light connector and the body ground in good condition?

YES : Go to Step 8.

NO : Repair the wiring harness.

STEP 6. Check ETACS-ECU connector C-304 [position light] or C-311 [tail light or license plate light] for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q : Is ETACS-ECU connector C-304 [position light] or C-311 [tail light or license plate light] in good condition?

YES : Go to Step 7.

NO : Repair the damaged parts.

STEP 7. Check wiring harness between headlight assembly connector, tail light connector or license plate light connector and ETACS-ECU connector.

Check the ground line for open circuit.
- Check the wiring harness between headlight assembly (LH) connector A-40 (terminal 4) and ETACS-ECU connector C-304 (terminal 3). [position light-LH]
- Check the wiring harness between headlight assembly (RH) connector A-57 (terminal 4) and ETACS-ECU connector C-304 (terminal 7). [position light-RH
- Check the wiring harness between tail light (LH) connector F-24 (terminal 2) and ETACS-ECU connector C-311 (terminal 10). [tail light-LH]

NOTE: Also check intermediate connectors D-17 and F-27 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector D-17 or F-27 is damaged, repair or replace the connector as described in General (Electrical), Harness Connector Inspection.

- Check the wiring harness between tail light (RH) connector F-07 (terminal 2) and ETACS-ECU connector C-311 (terminal 13).[tail light-RH]

NOTE: Also check intermediate connectors D-17 and F-27 and joint connector C-43 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector D-17 or F-27 or joint connector C-43 is damaged, repair or replace the connector as described in General (Electrical), Harness Connector Inspection.
- Check the wiring harness between license plate light (LH) connector F-18 (terminal 2) and ETACS-ECU connector C-311 (terminal 10). [license plate light-LH]

NOTE: Also check intermediate connectors D-17 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector D-17 is damaged, repair or replace the connector as described in General (Electrical), Harness Connector Inspection.

- Check the wiring harness between license plate light (RH) connector F-15 (terminal 2) and ETACS-ECU connector C-311 (terminal 10). [license plate light-RH]

NOTE: Also check intermediate connectors D-17 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector D-17 is damaged, repair or replace the connector as described in General (Electrical), Harness Connector Inspection.

Q : Is the wiring harness between headlight assembly connector, tail light connector or license plate light connector and ETACS-ECU connector in good condition?

YES : Go to Step 8.

NO : Repair the wiring harness.

STEP 8. Retest the system.

Check that the position light, tail light, or license plate light illuminate normally.

Q : Do the position light, tail light, or license plate light work normally?

YES (The light illuminate normally at both high and low beams.) : The trouble can be an intermittent malfunction (Refer to General (Body and Chassis) -How to use Troubleshooting/inspection Service Points -How to Cope with Intermittent Malfunction).

NO [When the position light does not illuminate] : Replace the position light socket.

NO [When the license plate light does not illuminate] : Replace the license plate light socket.

NO [When the tail lights do not illuminate] : Replace the rear side maker light socket.
pro multis Credits:Operation CHARM About Operation CHARM