P0183
DTC P0183: Fuel Tank Temperature Sensor Circuit High InputFuel Tank Temperature Sensor Circuit Part 1:
Fuel Tank Temperature Sensor Circuit Part 2:
CIRCUIT OPERATION
- 5-volt voltage is applied to the fuel tank temperature sensor output terminal (terminal No.3) from the ECM (terminal No.96) via the resistor in the ECM.
- The fuel tank temperature sensor output voltage increases when the resistance increases and decreases when the resistance decreases. The ground terminal (terminal No.2) is grounded to the vehicle body.
TECHNICAL DESCRIPTION
- The fuel tank temperature sensor converts the fuel tank temperature to a voltage.
- The ECM detects the fuel tank temperature in the fuel tank with this output voltage.
DESCRIPTIONS OF MONITOR METHODS
- Fuel tank temperature sensor output voltage is out of specified range.
MONITOR EXECUTION
- Continuous
MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
- Not applicable
Sensor (The sensor below is determined to be normal)
- Engine coolant temperature sensor
- Intake air temperature sensor
DTC SET CONDITIONS
Logic Flow Chart:
Logic Flow Chart
Check Condition
- 2 seconds or more have passed since the engine starting sequence was completed.
Judgment Criterion
- Fuel tank temperature sensor output voltage has continued to be 4.6 volts or higher for 2 seconds.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function - OBD-II Drive Cycle - Pattern 23. OBD-II Drive Cycle Pattern Lists
TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
- Fuel tank temperature sensor failed.
- Open fuel tank temperature sensor circuit, harness damage, or connector damage.
- ECM failed.
DIAGNOSIS
Required Special Tools:
- MB991958: Scan Tool (M.U.T.-III Sub Assembly)
- MB991824: V.C.I.
- MB991827: USB Cable
- MB991911: Main Harness B
STEP 1. Using scan tool MB991958, check data list item 4A: Fuel Tank Temperature Sensor.
CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch to the "ON" position.
3. Set scan tool MB991958 to the data reading mode for item 4A, Fuel Tank Temperature Sensor.
- With the engine cool, the fuel tank temperature should be approximately the same as ambient air temperature.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES: It can be assumed that this malfunction is intermittent.
NO: Go to Step 2.
STEP 2. Check harness connector D-36 at the fuel tank temperature sensor for damage.
Q: Is the harness connector in good condition?
YES: Go to Step 3.
NO: Repair or replace it. Then go to Step 11.
STEP 3. Check the fuel tank temperature sensor.
1. Disconnect the fuel tank temperature sensor connector D-36.
2. Measure the resistance between terminal No.2 and No.3 of the fuel tank temperature sensor.
Standard value: 0.5 - 12.0 kOhms
Q: Is the measured resistance between 0.5 and 12.0 kOhms?
YES: Go to Step 4.
NO: Replace the fuel tank temperature sensor. Then go to Step 11.
STEP 4. Measure the sensor supply voltage at fuel tank temperature sensor harness side connector D-36.
1. Disconnect connector D-36 and measure at the harness side.
2. Turn the ignition switch to the "ON" position.
3. Measure the voltage between terminal No.3 and ground.
- Voltage should be between 4.5 and 4.9 volts
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.5 and 4.9 volts?
YES: Go to Step 8.
NO: Go to Step 5.
STEP 5. Measure the sensor supply voltage at ECM connector C-117 by backprobing.
1. Do not disconnect the ECM connector C-117.
2. Disconnect the fuel tank temperature sensor connector D-10.
3. Turn the ignition switch to the "ON" position.
4. Measure the voltage between terminal No.96 and ground by backprobing.
- Voltage should be between 4.5 and 4.9 volts.
5. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.5 and 4.9 volts?
YES: Go to Step 6.
NO: Go to Step 7.
STEP 6. Check harness connector C-117 at ECM for damage.
Q: Is the harness connector in good condition?
YES: Check harness connectors C-113, C-122 and D-35 at intermediate connectors for damage, and repair or replace as required. If the intermediate connectors are in good condition, repair the harness wire between fuel tank temperature sensor connector D-36 (terminal No.3) and ECM connector C-117 (terminal No.96) because of open circuit. Then go to Step 11.
NO: Repair or replace it. Then go to Step 11.
STEP 7. Check harness connector C-117 at ECM for damage.
Q: Is the harness connector in good condition?
YES: Replace the ECM. Then go to Step 11.
NO: Repair or replace it. Then go to Step 11.
STEP 8. Check for continuity at fuel tank temperature sensor harness side connector D-36.
1. Disconnect connector D-36 and measure at the harness side.
2. Check for the continuity between terminal No.2 and ground.
- Should be less than 2 Ohms.
Q: Does continuity exist?
YES: Go to Step 9.
NO: Check connector D-34 at intermediate connector for damage, and repair or replace as required. If the intermediate connector is in good condition, repair the harness wire between fuel tank temperature sensor connector D-36 (terminal No.2) and ground because of open circuit or harness damage. Then go to Step 11.
STEP 9. Check harness connector C-117 at ECM for damage.
Q: Is the harness connector in good condition?
YES: Go to Step 10.
NO: Repair or replace it. Then go to Step 11.
STEP 10. Check for open circuit and harness damage between fuel tank temperature sensor connector D-36 (terminal No.3) and ECM connector C-117 (terminal No.96).
NOTE: Check harness after checking intermediate connectors C-113, C-122 and D-35. If any of the intermediate connectors are damaged, repair or replace it. Then go to Step 11.
Q: Is the harness wire in good condition?
YES: Replace the ECM. Then go to Step 11.
NO: Repair it. Then go to Step 11.
STEP 11. Test the OBD-II drive cycle.
1. Carry out a test drive with the drive cycle pattern. Refer to, Diagnostic Function - OBD-II Drive Cycle - Pattern 23. OBD-II Drive Cycle Pattern Lists
2. Check the diagnostic trouble code (DTC).
Q: Is DTC P0183 set?
YES: Retry the troubleshooting.
NO: The inspection is complete.