Pinpoint Test AU: DTC B1318 Or DTC U3003:16 (Front Controls Interface Module (FCIM))
Information and Entertainment System
Pinpoint Test AU: DTC B1318 Or DTC U3003:16 (Front Controls Interface Module (FCIM))
Refer to Wiring Diagram Set 130 (Fusion/Milan/MKZ, Fusion Hybrid, Milan Hybrid, MKZ Hybrid), Audio System/Navigation for schematic and connector information. Diagrams By Number
Normal Operation
- DTC B1318 (Battery Voltage Low) - set by the non-navigation (Fusion, Milan) Front Controls Interface Module (FCIM) when the supply voltage falls below 10 volts for greater than 10 seconds during normal operation or during the self-test.
- DTC U3003:16 (Battery Voltage: Circuit Voltage Below Threshold) - set by the non-navigation (MKZ) or navigation (all) FCIM when the supply voltage falls below 10 volts for greater than 10 seconds during normal operation or for greater than 250 milliseconds during the self-test.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- High circuit resistance
- FCIM
PINPOINT TEST AU: DTC B1318 OR DTC U3003:16 (FCIM)
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: Failure to disconnect the battery when instructed will result in false resistance readings. Refer to Battery, Mounting and Cables Battery Disconnect.
-------------------------------------------------
AU1 RECHECK THE FCIM DTCs
- Clear the FCIM DTCs.
- Ignition OFF.
- Ignition ON.
- Wait at least 15 seconds.
- Repeat the FCIM self-test.
- Is DTC B1318 or DTC U3003:16 still present?
Yes
GO to AU2.
No
The system is operating correctly at this time. The DTC may have set due to a previous low battery voltage condition.
-------------------------------------------------
AU2 CHECK FOR CHARGING SYSTEM DTCs IN THE PCM
- Retrieve the continuous memory DTCs from all modules.
- Is DTC P0620, P0622, P0625, or P065B set in the PCM?
Yes
REFER to Charging System Testing and Inspection.
No
GO to AU3.
-------------------------------------------------
AU3 CHECK THE BATTERY CONDITION AND STATE OF CHARGE
- Check the battery condition and verify that the battery is fully charged. Refer to Battery, Mounting and Cables Testing and Inspection.
- Is the battery OK and fully charged?
Yes
GO to AU4.
No
REFER to Battery, Mounting and Cables Testing and Inspection.
-------------------------------------------------
AU4 CHECK THE FCIM VOLTAGE SUPPLY
- Ignition OFF.
- Measure and record the voltage at the battery.
- Disconnect: FCIM C2403 (Fusion/Milan Without Navigation), C2408 (Fusion/Milan With Navigation), or C2402 (MKZ) .
- Ignition ON.
- Measure the voltage between the FCIM, harness side and ground as follows:
- Is the voltage within 0.2 volt of the recorded battery voltage?
Yes
GO to AU5.
No
REPAIR the circuit for high resistance. CLEAR the DTC. REPEAT the self-test.
-------------------------------------------------
AU5 CHECK THE FCIM GROUND CIRCUIT FOR CONTINUITY
- Ignition OFF.
- Disconnect: Negative Battery Cable .
- Measure the resistance between the FCIM, harness side and ground as follows:
- Is the resistance less than 5 ohms?
Yes
GO to AU6.
No
REPAIR the circuit for high resistance. TEST the system for normal operation.
-------------------------------------------------
AU6 CHECK FOR CORRECT FCIM OPERATION
- Disconnect the FCIM connector.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect the FCIM connector and make sure it seats correctly.
- Is the concern still present?
Yes
INSTALL a new FCIM. REFER to Front Controls Interface Module (FCIM) - Fusion, Milan Front Controls Interface Module (FCIM) or Front Controls Interface Module (FCIM) - MKZ Front Controls Interface Module (FCIM). TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
-------------------------------------------------