Installation

1UR-FSE EXHAUST: EXHAUST MANIFOLD (for 2WD): INSTALLATION

1. INSTALL AIR FUEL RATIO SENSOR (for Bank 1) Installation

2. INSTALL AIR FUEL RATIO SENSOR (for Bank 2) Installation

3. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

(a) Install a new gasket.

LH:

(b) Install the exhaust manifold LH, and install 8 new nuts in the order shown in the illustration.

Torque : 21 Nm (214 kgf-cm, 15 ft-lbf)

4. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR





(a) Install the exhaust manifold heat insulator with the 3 bolts.

Torque : 10 Nm (102 kgf-cm, 7 ft-lbf)

(b) Connect the air fuel ratio sensor connector.





5. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

(a) Install a new gasket.

RH:

(b) Install the exhaust manifold RH, and install 8 new nuts in the order shown in the illustration.

Torque : 21 Nm (214 kgf-cm, 15 ft-lbf)

6. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR





(a) Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

Torque : 10 Nm (102 kgf-cm, 7 ft-lbf)

(b) Connect the air fuel ratio sensor connector.





7. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE Installation

8. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (w/ VGRS) Installation

9. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (w/o VGRS) Installation

10. INSTALL STEERING SLIDING YOKE WITH SHAFT SUB-ASSEMBLY (w/ VGRS) Installation

11. INSTALL STEERING SLIDING YOKE WITH SHAFT SUB-ASSEMBLY (w/o VGRS) Installation

12. INSTALL GENERATOR ASSEMBLY Installation

13. INSTALL V-RIBBED BELT Installation

14. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH Installation

15. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH Installation

16. INSTALL FRONT STABILIZER BAR NO. 1 BUSH Installation

17. TEMPORARILY TIGHTEN FRONT STABILIZER BAR Installation

18. TIGHTEN FRONT STABILIZER NO. 1 BRACKET LH Installation

19. TIGHTEN FRONT STABILIZER NO. 1 BRACKET RH Installation

20. INSTALL REAR ENGINE UNDER COVER LH Installation

21. INSTALL REAR ENGINE UNDER COVER RH Installation

22. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY Installation

23. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY RH Installation

24. INSTALL FRONT EXHAUST PIPE ASSEMBLY Installation

25. INSTALL FRONT FLOOR CENTER BRACE Installation

26. CONNECT HEATED OXYGEN SENSOR (for Sensor 2) Installation

27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

28. INSTALL COWL TOP VENTILATOR LOUVER RH Installation

29. INSPECT FOR EXHAUST GAS LEAK

30. INSTALL FRONT FLOOR COVER RH Installation

31. INSTALL FRONT FLOOR COVER LH Installation

32. INSTALL REAR FLOOR SIDE MEMBER COVER RH Installation

33. INSTALL REAR FLOOR SIDE MEMBER COVER LH Installation

34. INSTALL NO. 5 ROCKER PANEL MOULDING PROTECTOR Installation

35. INSTALL NO. 6 ROCKER PANEL MOULDING PROTECTOR Installation

36. INSTALL NO. 1 DIFFERENTIAL SUPPORT PROTECTOR Installation

37. INSTALL NO. 2 DIFFERENTIAL SUPPORT PROTECTOR Installation

38. INSTALL NO. 2 ENGINE UNDER COVER Installation

39. INSTALL FRONT SUSPENSION MEMBER PROTECTOR LOWER Installation

40. INSTALL NO. 1 ENGINE UNDER COVER Service and Repair

41. INSTALL FRONT WHEEL Installation

42. INSTALL ENGINE ROOM SIDE COVER RH Installation

43. INSTALL ENGINE ROOM SIDE COVER LH Installation

44. INSTALL INTAKE AIR CONNECTOR PIPE Installation

45. INSTALL NO. 1 AIR CLEANER INLET Installation

46. INSTALL AIR CLEANER INLET COVER Installation

47. INSTALL V-BANK COVER SUB-ASSEMBLY Installation

48. PERFORM INITIALIZATION

(a) Perform initialization Repair Instruction - Initialization.

NOTICE:
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.