Installation
SEAT BELT: REAR SEAT OUTER BELT ASSEMBLY: INSTALLATION
1. INSTALL REAR SEAT OUTER BELT ASSEMBLY CENTER
(a) Align the seat belt positioning hole with the claw.
(b) Temporarily install the outer belt with the 2 bolts.
(c) Tighten the rear side bolt first, then the front side bolt to install the outer belt.
for rear bolt - Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
for front bolt - Torque : 7.5 Nm (77 kgf-cm, 66 in-lbf)
2. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
(a) Insert the claw of the retractor (a) into the hole.
(b) Align the seat belt positioning hole with the claw and install the retractor of the seat belt with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
(c) Connect the pretensioner connector, as shown in the illustration.
3. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
(a) Insert the claw of the retractor (a) into the hole.
(b) Align the seat belt positioning hole with the claw and install the retractor of the seat belt with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
(c) Connect the pretensioner connector, as shown in the illustration.
4. INSTALL NO. 4 AIR DUCT REAR (w/ Rear Cooler) Installation
5. INSTALL NO. 5 AIR DUCT REAR (w/ Rear Cooler) Installation
6. INSTALL ROOF SIDE NO. 2 AIR DUCT LH (w/ Rear Cooler) Installation
7. INSTALL ROOF SIDE NO. 2 AIR DUCT RH (w/ Rear Cooler) Installation
8. INSTALL NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade) Installation
9. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade) Installation
10. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)
(a) Except 4-Passenger with Ottoman:
(1) Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
(2) Attach the 5 claws and 2 clips to install the package tray trim panel assembly.
(3) Attach the 4 claws to install the 3 belt guides.
(b) for 4-Passenger Ottoman:
(1) Pass the 2 rear seat belt floor anchors through the package tray trim panel assembly.
(2) Attach the 5 claws and 2 clips to install the package tray trim panel assembly.
(3) Attach the 4 claws to install the 2 belt guides.
11. INSTALL ROOF SIDE GARNISH INNER LH Installation
12. INSTALL ROOF SIDE GARNISH INNER RH Installation
13. INSTALL REAR SEAT SIDE GARNISH LH Installation
14. INSTALL REAR SEAT SIDE GARNISH RH Installation
15. INSTALL REAR DOOR SCUFF PLATE LH
(a) for Standard Body:
Install the rear door scuff plate Installation.
(b) for Long Body:
Install the rear door scuff plate Installation.
16. INSTALL REAR DOOR SCUFF PLATE RH
(a) for Standard Body:
Install the rear door scuff plate Installation.
(b) for Long Body:
Install the rear door scuff plate Installation.
17. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type) Installation
18. INSTALL REAR SEATBACK ASSEMBLY LH (for Power Seat) Installation
19. INSTALL REAR SEATBACK ASSEMBLY RH (for Power Seat) Installation
20. INSTALL REAR SEATBACK ASSEMBLY LH (for Ottoman) Installation
21. INSTALL REAR SEATBACK ASSEMBLY RH (for Ottoman) Installation
22. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
(a) Install the floor end of the rear seat outer belt assembly LH with the bolt.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTICE:
Do not allow the anchor part of the rear seat 3 point type belt assembly LH to overlap the protruding parts of the floor panel.
(b) Check if the ELR locks.
NOTICE:
The check should be performed with the outer belt assembly installed.
(1) With the belt assembly installed, check that the belt locks when it is pulled out quickly.
23. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT
Use the same procedures described for the LH side.
24. CONNECT REAR SEAT OUTER BELT ASSEMBLY CENTER
(a) for Power Seat:
Install the floor end of the rear seat outer belt assembly center with the nut.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTICE:
Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.
(b) for Fixed Seat Type:
Install the floor end of the rear seat outer belt assembly center with the nut.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTICE:
Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.
(c) Check if the ELR locks.
NOTICE:
The check should be performed with the outer belt assembly installed.
(1) With the belt assembly installed, check that the belt locks when it is pulled out quickly.
25. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type) Installation
26. INSTALL REAR SEAT CUSHION ASSEMBLY LH
(a) for Power Seat:
(1) Remove the rear seat cushion assembly Installation.
(b) for Ottoman Seat:
(1) Remove the rear seat cushion assembly Installation.
27. INSTALL REAR SEAT CUSHION ASSEMBLY RH
(a) for Power Seat:
(1) Remove the rear seat cushion assembly Installation.
(b) for Ottoman Seat:
(1) Remove the rear seat cushion assembly Installation.
28. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.
29. INSTALL COWL TOP VENTILATOR LOUVER RH Installation