Stop Light Does Not Illuminate
LIGHTING: LIGHTING SYSTEM: Stop Light does not Illuminate
- Stop Light does not Illuminate
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Check if DTC B2402 is output. If output, refer to the following procedures B2402.
HINT
With the engine switch off, if the rear junction block ECU is in sleep mode or is malfunctioning, the fail-safe line in the rear junction block ECU operates light illuminations.
PROCEDURE
1. PERFORM ACTIVE TEST USING TECHSTREAM (STOP LIGHT)
(a) Using the Techstream, perform the Active Test.
Body No.4
OK:
Stop light condition is switched by Active Test.
B -- READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
A -- Continue to next step.
2. CHECK HARNESS AND CONNECTOR (BATTERY - REAR JUNCTION BLOCK ECU)
(a) Disconnect the LH ECU connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard voltage:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
3. CONFIRM LIGHT POSITION
(a) Check the malfunctioning stop light.
Result
B -- CHECK REAR JUNCTION BLOCK ECU (STP3 VOLTAGE)
C -- CHECK REAR JUNCTION BLOCK ECU (STP4 VOLTAGE)
D -- READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
E -- CHECK DTC (BRAKE CONTROL SYSTEM)
A -- Continue to next step.
4. CHECK REAR JUNCTION BLOCK ECU (STP1, STP2 VOLTAGE)
(a) Disconnect the S64 ECU connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard voltage:
NG -- REPLACE LUGGAGE ROOM JUNCTION BLOCK (REAR JUNCTION BLOCK ECU)
OK -- Continue to next step.
5. CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - REAR JUNCTION BLOCK ECU AND BODY GROUND)
(a) Disconnect the S64 ECU connector.
(b) Disconnect the S51 and S52 light connectors.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
for LH
for RH
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE REAR COMBINATION LIGHT ASSEMBLY Removal
6. CHECK REAR JUNCTION BLOCK ECU (STP3 VOLTAGE)
(a) Disconnect the S63 ECU connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard voltage:
NG -- REPLACE LUGGAGE ROOM JUNCTION BLOCK (REAR JUNCTION BLOCK ECU)
OK -- Continue to next step.
7. CHECK HARNESS AND CONNECTOR (REAR LIGHT - REAR JUNCTION BLOCK ECU AND BODY GROUND)
(a) Disconnect the S63 ECU connector.
(b) Disconnect the S33 and S41 light connectors.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
for LH
for RH
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE REAR LIGHT ASSEMBLY Removal
8. CHECK REAR JUNCTION BLOCK ECU (STP4 VOLTAGE)
(a) Remove the S62 ECU with its connector still connected.
(b) Measure the voltage according to the value(s) in the table below.
Standard voltage:
NG -- REPLACE LUGGAGE ROOM JUNCTION BLOCK (REAR JUNCTION BLOCK ECU)
OK -- Continue to next step.
9. CHECK HARNESS AND CONNECTOR (CENTER STOP LIGHT - REAR JUNCTION BLOCK ECU AND BODY GROUND)
(a) Disconnect the S62 ECU connector.
(b) Disconnect the S20 light connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE CENTER STOP LIGHT ASSEMBLY Removal
10. READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
(a) Using the Techstream, read the Data List.
Body No.4
OK:
Condition sign can be displayed.
NG -- INSPECT STOP LIGHT SWITCH ASSEMBLY
OK -- REPLACE LUGGAGE ROOM JUNCTION BLOCK (REAR JUNCTION BLOCK ECU)
11. INSPECT STOP LIGHT SWITCH ASSEMBLY
(a) Remove the stop light switch Removal.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPLACE STOP LIGHT SWITCH ASSEMBLY Removal
OK -- Continue to next step.
12. CHECK HARNESS AND CONNECTOR (BATTERY - STOP LIGHT SWITCH)
(a) Disconnect the A35 switch connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard voltage:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
13. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - REAR JUNCTION BLOCK ECU)
(a) Disconnect the S62 ECU connector.
(b) Disconnect the A35 switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE LUGGAGE ROOM JUNCTION BLOCK ASSEMBLY (REAR JUNCTION BLOCK ECU)
14. CHECK DTC (BRAKE CONTROL SYSTEM)
(a) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.
(b) Check for DTCs Reading and Clearing Diagnostic Trouble Codes.
OK:
DTCs output does not occur.
NG -- GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM Electronically Controlled Brake System
OK -- Continue to next step.
15. CHECK STOP LIGHT
(a) With the skid control ECU connector disconnected, check the illumination of the stop lights when depressing the brake pedal.
OK:
Stop lights operate normally when the brake pedal is depressed.
NG -- REPLACE LUGGAGE ROOM JUNCTION BLOCK (REAR JUNCTION BLOCK ECU)
OK -- REPLACE SKID CONTROL ECU ASSEMBLY Removal