Removal

1UR-FSE EXHAUST: EXHAUST PIPE: REMOVAL

CAUTION:
* The procedures should be performed by at least 2 people.
* Wear protective gloves when removing the exhaust pipe.
* The exhaust pipe is extremely hot immediately after the engine has stopped.
* Confirm that the exhaust pipe has cooled down before removing it.
1. REMOVE NO. 2 DIFFERENTIAL SUPPORT PROTECTOR Removal

2. REMOVE NO. 1 DIFFERENTIAL SUPPORT PROTECTOR Removal

3. REMOVE NO. 6 ROCKER PANEL MOULDING PROTECTOR

(a) Remove the 2 clips, screw and protector.

4. REMOVE NO. 5 ROCKER PANEL MOULDING PROTECTOR

(a) Remove the 2 clips, screw and protector.

5. REMOVE REAR FLOOR SIDE MEMBER COVER LH

(a) Remove the clip, nut, 2 screws, 3 bolts and cover.

6. REMOVE REAR FLOOR SIDE MEMBER COVER RH

(a) Remove the clip, nut, 2 screws, 3 bolts and cover.

7. REMOVE FRONT FLOOR COVER LH

(a) Remove the 3 hole seals, 4 grommets and cover.

8. REMOVE FRONT FLOOR COVER RH

(a) Remove the 3 hole seals, 4 grommets and cover.

9. REMOVE FRONT FLOOR CENTER BRACE

(a) Remove the 4 bolts and brace.

10. REMOVE FRONT CENTER FLOOR COVER (for AWD) Removal

11. DISCONNECT HEATED OXYGEN SENSOR (for 2WD)

(a) Disconnect the 2 grommets from the floor panel.

(b) Using SST, loosen the sensors, and then disconnect the sensors by hand.

HINT
Rotate the sensor counterclockwise to remove it from the front exhaust pipe, and record how many times it was rotated.

NOTICE:
Do not strike the metal part of the sensor.

SST : 09224-00010

12. DISCONNECT HEATED OXYGEN SENSOR (for AWD)

(a) for Bank 1:

Disconnect the sensor connector.

(b) for Bank 2:

Disconnect the grommet from the floor panel.

Using SST, loosen the sensor, and then disconnect the sensor by hand.

HINT
Rotate the sensor counterclockwise to remove it from the front exhaust pipe, and record how many times it was rotated.

NOTICE:
Do not strike the metal part of the sensor.

13. REMOVE FRONT EXHAUST PIPE ASSEMBLY

(a) Temporarily loosen the 8 bolts on the tailpipe and manifold sides.

(b) Remove the 4 nuts and 4 bolts from the exhaust manifold LH and RH.

HINT
During removal, hold the exhaust pipe.

HINT
During removal, hold the exhaust pipe.

(d) Remove the 2 gaskets from the exhaust manifold side, and the 2 gaskets from the tailpipe side.

14. REMOVE HEATED OXYGEN SENSOR (for AWD)

NOTICE:
Do not strike the metal part of the sensor.

(a) for Bank 1:

Using SST, loosen the sensor and then remove the sensor by hand.

SST : 09224-00010

15. REMOVE TAILPIPE LH

(a) Disconnect the 3 exhaust pipe support and remove the tail pipe.

16. REMOVE TAILPIPE RH

(a) Disconnect the 3 exhaust pipe support and remove the tail pipe.

17. REMOVE EXHAUST PIPE DAMPER

(a) Remove the 2 bolts and exhaust pipe damper from the tailpipe LH.

(b) Remove the 2 bolts and exhaust pipe damper from the tailpipe RH.

18. REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY (for 2WD)

(a) Remove the 2 bolts and bracket.