FREE REPAIR MANUALS & LABOR GUIDES 1982-2013 Vehicles
Courtesy of Operation CHARM: Car repair manuals for everyone.
Home >> Lexus >> 2011 >> GS 350 RWD V6-3.5L (2GR-FSE) >> Repair and Diagnosis >> Body and Frame >> Interior Moulding / Trim >> Headliner >> Service and Repair >> Installation

Installation





INTERIOR: ROOF HEADLINING: INSTALLATION

1. INSTALL ROOF NO.1 WIRE

(a) With Compass:

(1) Install the inner mirror wire.





(b) Only when replacing the roof headlining.

Install the roof wire.

HINT
When removing peeling paper from double-sided tape, do not allow foreign matter to contact the tape's adhesive.

(1) Remove the peeling paper from one side of double-sided tape A.

(2) Attach double-sided tape A to the marks on the roof headlining, as shown in the illustrations below.

(3) Remove peeling paper from the other side of double-sided tape A.

(4) Align the wire harness to double-sided tape A. Also, align the marking tape areas of the wire harness to the marks on the roof headlining (see A, B and C in the illustrations below). Temporarily attach the wire harness to the roof headlining.

(5) Remove peeling paper from one side of double-sided tape B. Secure the wire harness to the roof headlining by attaching double-sided tape B to the wire harness and marks on the roof headlining, as shown in A, B and C in the illustrations below.

(6) Align the marking tape area of the wire harness to the roof headlining installation part, as shown in D in the illustrations below. Wrap tape around the wire harness and installation part.

(7) Attach the claw of the vanity light assembly to install it.

CAUTION:
Securely install the roof No. 1 wire. If there is any slack, noise will occur.









2. INSTALL VANITY LIGHT ASSEMBLY

3. INSTALL ROOF HEADLINING ASSEMBLY





(a) Apply double-sided tape to the pads.

(b) Align the pads with the markings on the roof headlining, and then install the pads.





Only when replacing the sliding roof housing:

(1) Remove the 11 fasteners from the removed sliding roof housing, and attach them to the roof headlining.

(c) Place the roof headlining in the through from the rear door.

(d) Without sliding roof:

Attach the 2 hooks and 4 clips to the vehicle body.

(e) With sliding roof:

Attach the hook, claw and 4 clips to the vehicle body.

(f) Only when replacing the roof headlining:

Remove the 11 fasteners from the removed roof headlining, and attach them to the new roof headlining.

(g) Attach the clips on the rear side of the vehicle.

(h) With sliding roof:

Install the roof headlining to the sliding roof housing.

(i) Attach the clamp of the roof wire to the front pillar garnish LH. Then connect the connector.

(j) With sliding roof:

Connect the connector to the sliding roof drive gear.





4. INSTALL VISOR HOLDER

5. INSTALL VISOR ASSEMBLY LH

(a) Install the visor with the 2 screws.

6. INSTALL VISOR ASSEMBLY RH

(a) Install the visor with the 2 screws.

7. INSTALL VISOR BRACKET COVER

(a) Attach the 4 claws to install the cover.

8. INSTALL STEERING SPOTLIGHT ASSEMBLY

(a) Connect the connector.

(b) Attach the 2 claws to install the spotlight.

9. INSTALL ASSIST GRIP ASSEMBLY

10. INSTALL REAR ROOM LIGHT ASSEMBLY

(a) Connect the connector.

(b) Attach the 4 claws to install the room light to the vehicle body.

11. INSTALL REAR VIEW MIRROR ASSEMBLY INNER

12. INSTALL PERSONAL LIGHT ASSEMBLY

(a) Connect the connector.

(b) Attach the 3 claws and 2 clips, and install the personal light.

(c) Install the 2 screws and 2 covers to personal light.

13. INSTALL FRONT ROOF TOP GARNISH

(a) Attach the 3 claws and 2 clips, and install the top garnish.

14. INSTALL REAR VIEW MIRROR COVER INNER

15. INSTALL ROOF SIDE GARNISH INNER LH

(a) Attach the 2 claws and 4 clips, and install the garnish.

16. INSTALL ROOF SIDE GARNISH INNER RH

HINT
Use the same procedures described for the LH side.

17. INSTALL REAR SEAT SIDE GARNISH LH





(a) Attach the 5 claws and install the garnish.

(b) Pull out the folded lip of the weatherstrip.

18. INSTALL REAR SEAT SIDE GARNISH RH

HINT
Use the same procedures described for the LH side.

19. INSTALL CENTER PILLAR GARNISH LH

(a) Attach the 2 claws to install the garnish.

(b) Install the 2 screws.

(c) Pull out the folded of the weatherstrip.

20. INSTALL CENTER PILLAR GARNISH RH

HINT
Use the same procedures described for the LH side.

21. INSTALL CENTER PILLAR GARNISH LOWER LH

(a) Attach the 2 claws and 5 clips to install the garnish.

(b) Pull out the folded of the weatherstrip.

22. INSTALL CENTER PILLAR GARNISH LOWER RH

HINT
Use the same procedures described for the LH side.

23. INSTALL REAR DOOR SCUFF PLATE LH





(a) Attach the 5claws to install the scuff plate.

(b) Pull out the folded lip of the weatherstrip.

24. INSTALL REAR DOOR SCUFF PLATE RH

HINT
Use the same procedures described for the LH side.

25. INSTALL FRONT PILLAR GARNISH LH





(a) Attach a new clip A to the vehicle body.

(b) Set the pillar garnish to the area labeled B. Using needle-nose pliers, install clip A to the pillar garnish and rotate it 90°.

(c) Install the pillar garnish by attaching the claws and clip.

(d) Pull out the folded lip of the weatherstrip.

26. INSTALL FRONT PILLAR GARNISH RH

HINT
Use the same procedures described for the LH side.

27. INSTALL FRONT DOOR OPENING TRIM COVER LH

(a) Attach the 3 claws to install the trim cover.

(b) Pull out the folded lip of the weatherstrip.

28. INSTALL FRONT DOOR OPENING TRIM COVER RH

HINT
Use the same procedures described for the LH side.

29. INSTALL FRONT DOOR SCUFF PLATE LH





(a) Attach the 5 claws and install the scuff plate.

(b) Pull out the folded lip of the weatherstrip.

30. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedures described for the LH side.

31. INSTALL CONSOLE BOX

Install console box. Installation

32. INSTALL REAR SEATBACK ASSEMBLY Installation

33. INSTALL REAR SEAT HEADREST ASSEMBLY CENTER

34. INSTALL REAR SEAT HEADREST ASSEMBLY LH

35. INSTALL REAR SEAT HEADREST ASSEMBLY RH

36. INSTALL REAR SEAT CUSHION ASSEMBLY Installation

37. INSTALL FRONT SEAT ASSEMBLY

Install front seat assembly. Installation

38. INSPECT FRONT POWER SEAT ASSEMBLY

Inspect front power seat assembly. Front Power Seat Control System

Inspect front power seat assembly (w/ seat position memory system). Front Power Seat Control System (w/ Seat Position Memory System)

39. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

40. INSPECT FUNCTION OF SEAT BELT

Inspect function of seat belt. Component Tests and General Diagnostics

41. INSPECT SEAT HEATER

Inspect seat heater. Testing and Inspection

42. PERFORM INITIALIZATION

Perform initialization. Repair Instruction - Initialization

NOTICE:
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.

pro multis Credits:Operation CHARM About Operation CHARM