Smart Access System With Push-Button Start (For Start Function)

THEFT DETERRENT / KEYLESS ENTRY: SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Start Function): CUSTOMIZE PARAMETERS

1. CUSTOMIZE SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Start Function)

HINT
The following items can be customized.

NOTICE:
* When the customer requests a change in a function, first make sure that the function can be customized.
* Record the current settings before customizing.

(a) Customizing with the Techstream

(1) Connect the Techstream to the DLC3.

(2) Turn the power switch on (IG).

(3) Turn the Techstream on.

(4) Enter the following menus: Customize Setting / Smart key/Access or Warning.

(5) Select the setting by referring to the table below.





(b) Customizing with the multi-display (w/Navigation System (for HDD))

(1) Turn the power switch on (IG).

(2) Enter the following menus: Setup / Vehicle / Vehicle Customization.

(3) Select the setting by referring to the table below.





(c) Customizing with the Combination meter assembly (w/o Navigation System (for HDD))

HINT
* Press and hold the DISP switch (steering pad switch assembly) when entering an item.
* Briefly press the DISP switch (steering pad switch assembly) when selecting an item.

(1) Turn the power switch on (IG).

(2) Enter the following menus: Settings / Vehicle Settings

(3) Select the setting by referring to the table below.





(4) Press and hold the DISP (steering pad switch assembly).

(5) The setting completion screen will be displayed.

(6) Return to the item selection screen.

(d) Entry cancel function (manual operation)

NOTICE:
Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.

HINT
While the smart access system with push-button start is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the key against the power switch.

(1) The following functions are disabled when the smart access system with push-button start is canceled.

1 Entry unlock/lock functions

2 Push start function

3 Key lock-in prevention function

4 Entry warning functions

(2) When canceling the system through manual operation:

1 Make sure the following conditions are met:

* The power switch is off.

* The driver door is closed.

* The driver door is unlocked.

2 Press the unlock button of the key.

3 Open the driver door within 5 seconds of completing the step above (driver door: closed at beginning of step -> opened).

4 With the driver door open, press the unlock button of the key 2 times within 5 seconds of completing the step above.

NOTICE:
If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

5 Close and open the driver door twice within 30 seconds of completing the above step (driver door: open at beginning of step -> closed -> opened -> closed -> opened).

6 With the driver door open, press the unlock button of the key 2 times within 30 seconds of completing the step above.

NOTICE:
If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

7 Close and open the driver door within 30 seconds of completing the step above (driver door: open at beginning of step -> closed -> opened).

8 Close the driver door within 5 seconds of completing the above step.

9 Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart access system with push-button start has been canceled.

(3) Perform the following procedure to restore the smart access system with push-button start to the active state from the canceled state.

1 Perform the procedures to cancel the smart access system with push-button start again.

2 Check that the wireless buzzer sounds once (short beep) to confirm that the smart access system with push-button start has been restored to the active state.

HINT
* The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
* The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.