Installation

WINDOW / GLASS: BACK WINDOW GLASS: INSTALLATION

1. INSTALL BACK WINDOW OUTSIDE MOULDING

(a) Apply Primer G to the installation part of a new back window outside moulding.

HINT
If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

(b) Install the new back window outside moulding onto the back window glass as shown in the illustration.





Text in Illustration





Standard Dimension:





NOTICE:
* Allow the primer to dry for 3 minutes or more.
* Do not keep any of the opened Primer G for later use.
* Do not apply too much primer.
HINT
Use the same procedure for the RH side and the LH side.

2. INSTALL BACK WINDOW GLASS ADHESIVE DAM

(a) Apply Primer G to the installation part of a new back window glass adhesive dam.

HINT
If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

(b) Install the new back window glass adhesive dam, applying double-sided tape all the way around the glass except where the dam is installed, as shown in the illustration.





Text in Illustration





Standard Dimension:





NOTICE:
* Do not apply too much primer.
* Allow the primer coating to dry for 3 minutes or more.
* Do not keep any of the opened Primer G for later use.
3. INSTALL BACK WINDOW LOWER OUTSIDE MOULDING

(a) Apply Primer G to the installation part of a new back window lower outside moulding.

HINT
If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

(b) Install the new back window lower outside moulding onto the back window glass as shown in the illustration.





Text in Illustration





NOTICE:
* Allow the primer to dry for 3 minutes or more.
* Do not keep any of the opened Primer G for later use.
* Do not apply too much primer.
4. INSTALL BACK WINDOW GLASS

(a) Using a brush, coat the installation surface on the vehicle body with Primer M.





Text in Illustration





NOTICE:
* Do not coat the adhesive with Primer M.
* Do not apply too much primer.
* Allow the primer coating to dry for 3 minutes or more.
* Do not keep any of the opened Primer M for later use.
HINT
If an area other than specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

(b) Using a brush or sponge, coat the adhesive application area with Primer G.





Text in Illustration





NOTICE:
* Do not apply too much primer.
* Allow the primer coating to dry for 3 minutes or more.
* Do not keep any of the opened Primer G for later use.
HINT
If an area other than specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

(c) Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent

(1) Cut off the tip of the cartridge nozzle as shown in the illustration.





Standard Dimension:





HINT
After cutting off the tip, use all adhesive within the time described in the table below.

Usage Time Frame:





(2) Load the sealer gun with the cartridge.

(3) Apply adhesive to the back window glass as shown in the illustration.





Text in Illustration





(d) Install the back window glass assembly.





(1) Install the back window glass assembly withe the 4 clips

NOTICE:
* Allow the primer coating to dry for 3 minutes or more.
* Check that the clips are attached to the body correctly.
* Check the clearance between the body and glass.
(2) Lightly press the front surface of the back window glass to ensure a close fit.

HINT
Press the glass with force of 98 N (10 kgf, 22 lbf) or more.

(3) Hold the back window glass using protective tape until the applied adhesive becomes hard.

NOTICE:
Do not drive the vehicle for the time described in the table below.

Minimum Time:





(e) Install the 2 nuts.





(f) Connect the 2 back window defogger connectors.





5. INSTALL BACK WINDOW PACKING

(a) Install the back window packing.





6. INSTALL QUARTER PILLAR GARNISH LH

7. INSTALL QUARTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

8. INSTALL REAR ROOF HEADLINING GARNISH

(a) Engage the 5clips to install the rear roof headlining garnish.





9. INSTALL ROOF SIDE INNER GARNISH LH

(a) Engage the 2 claws and 4 clips to install the roof side inner garnish LH.





10. INSTALL ROOF SIDE INNER GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

11. CLOSE METAL TOP ROOF

(a) Close the metal top roof.

12. INSPECT FOR LEAKS AND REPAIR

(a) After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

(b) If water leaks into the cabin, allow the water to dry and add adhesive.

(c) Remove the protective tape.