Installation
4GR-FSE INTAKE / EXHAUST: EXHAUST MANIFOLD: INSTALLATION
1. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1) Installation
2. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH
(a) Install a new gasket as shown in the illustration.
(b) Install the exhaust manifold sub-assembly LH with 6 new nuts.
LH:
Torque : 21 Nm (214 kgf-cm, 15 ft-lbf)
NOTICE:
* Do not damage the stud bolts when installing the exhaust manifold.
* Be sure to tighten either of nuts A first as show in the illustration.
(c) Connect the air fuel ratio sensor connector (for Bank 2 Sensor 1).
3. INSTALL NO. 3 ENGINE ROOM RELAY BLOCK
(a) Install the No. 3 engine room relay block with the bolt and nut.
Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)
(b) Install the earth wire with the 2 bolts.
Bolt A - Torque : 10 Nm (102 kgf-cm, 7 ft-lbf)
Bolt B - Torque : 13 Nm (133 kgf-cm, 10 ft-lbf)
4. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH
(a) Install a new gasket as shown in the illustration.
(b) Install the exhaust manifold sub-assembly RH with 6 new nuts.
RH:
Torque : 21 Nm (214 kgf-cm, 15 ft-lbf)
NOTICE:
* Do not damage the stud bolts when installing the exhaust manifold.
* Be sure to tighten either of nuts A first as show in the illustration.
5. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1) Installation
6. INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE Installation
7. INSTALL BATTERY TRAY Installation
8. INSTALL POWER STEERING ECU ASSEMBLY
(a) Install the power steering ECU assembly Installation.
9. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE Installation
10. INSTALL V-BANK COVER SUB-ASSEMBLY Installation
11. INSTALL ENGINE ROOM SIDE COVER LH Installation
12. INSTALL ENGINE ROOM SIDE COVER Installation
13. INSTALL COOL AIR INTAKE DUCT SEAL Installation
14. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY (for Automatic Transmission)
(a) Install the No. 1 exhaust pipe support bracket sub-assembly with the 2 bolts.
Torque : 43 Nm (440 kgf-cm, 32 ft-lbf)
15. INSTALL FRONT EXHAUST PIPE ASSEMBLY Installation
16. INSTALL FRONT CENTER FLOOR BRACE
(a) Install the front center floor brace with the 4 bolts.
Torque : 17 Nm (173 kgf-cm, 13 ft-lbf)
17. INSTALL REAR BODY SUPPORT BRACKET
(a) Install the 2 rear body support brackets with the 12 bolts except (A).
Torque : 17 Nm (173 kgf-cm, 13 ft-lbf)
(b) Install the 2 bolts (A).
Torque : 17 Nm (173 kgf-cm, 13 ft-lbf)
18. INSTALL NO. 2 ENGINE UNDER COVER
19. INSTALL NO. 1 BODY MOUNTING BRACKET SUB-ASSEMBLY LH Installation
20. INSTALL NO. 1 BODY MOUNTING BRACKET SUB-ASSEMBLY RH Installation
21. INSTALL NO. 2 FLOOR UNDER COVER Installation
22. INSTALL NO. 1 FLOOR UNDER COVER Installation
23. INSTALL FRONT FLOOR COVER LH Installation
24. INSTALL FRONT FLOOR COVER RH Installation
25. INSTALL ENGINE UNDER COVER
26. INSPECT FOR EXHAUST GAS LEAK