Installation
PARKING BRAKE: PARKING BRAKE PEDAL: INSTALLATION
1. INSTALL PARKING PEDAL PAD
(a) Engage the claw and install the parking pedal pad on the parking brake pedal.
2. INSTALL PARKING BRAKE PEDAL ASSEMBLY (for 2WD)
(a) Pass the No. 1 parking brake cable assembly through the parking brake pedal and hold the cable with the clip.
HINT
Fully tighten the No. 1 wire adjusting nut and lock nut when adjusting the parking brake pedal free play.
(b) Fully bend the parking brake pedal claw.
(c) Temporarily install the parking brake pedal by loosely tightening the 3 nuts.
(d) Fully tighten the 3 nuts in the order shown in the illustration.
Torque : 13 Nm (133 kgf-cm, 10 ft-lbf)
(e) Connect the parking brake switch connector.
(f) Install the instrument panel junction block assembly with the 2 nuts.
(g) Install the No. 1 parking brake cable assembly to the body with the 3 nuts and 2 bolts.
Nut - Torque : 6.0 Nm (61 kgf-cm, 53 in-lbf)
Bolt - Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)
(h) Install the parking brake equalizer to the No. 1 parking brake cable assembly.
(i) Slide the rubber boot back as shown in the illustration.
(j) Connect the 2 No. 2 parking brake cable assemblies to the parking brake equalizer.
(k) Install the 2 No. 2 parking brake cable assemblies with the 2 bolts.
Torque : 6.0 Nm (61 kgf-cm, 53 in-lbf)
(l) Install the parking brake return with damper spring.
3. INSTALL PARKING BRAKE PEDAL ASSEMBLY (for 4WD)
(a) Pass the No. 1 parking brake cable assembly through the parking brake pedal and hold the cable with the clip.
HINT
Fully tighten the No. 1 wire adjusting nut and lock nut when adjusting the parking brake pedal free play.
(b) Fully bend the parking brake pedal claw.
(c) Temporarily install the parking brake pedal by loosely tightening the 3 nuts.
(d) Fully tighten the 3 nuts in the order shown in the illustration.
Torque : 13 Nm (133 kgf-cm, 10 ft-lbf)
(e) Connect the parking brake switch connector.
(f) Install the instrument panel junction block assembly with the 2 nuts.
(g) Install the No. 1 parking brake cable assembly to the body with the 3 nuts and 2 bolts.
Nut - Torque : 6.0 Nm (61 kgf-cm, 53 in-lbf)
Bolt - Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)
(h) Install the parking brake equalizer to the No. 1 parking brake cable assembly.
(i) Slide the rubber boot back as shown in the illustration.
(j) Connect the 2 No. 2 parking brake cable assemblies to the parking brake equalizer.
(k) Install the 2 No. 2 parking brake cable assemblies with the 2 bolts.
Torque : 6.0 Nm (61 kgf-cm, 53 in-lbf)
(l) Install the parking brake return with damper spring.
4. INSTALL FRONT UPPER FLOOR REAR SUB PANEL
(a) Install the front floor rear upper sub panel with the 4 bolts.
Torque : 18 Nm (184 kgf-cm, 13 ft-lbf)
(b) Engage the 6 clamps.
5. INSTALL CENTER AIRBAG SENSOR ASSEMBLY Installation
6. INSTALL NO. 3 DASH PANEL INSULATOR PAD
(a) Install the No. 3 dash panel insulator pad.
7. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 2GR-FSE)
HINT
Installation.
8. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4GR-FSE)
HINT
Installation.
9. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
HINT
.
10. INSTALL NO. 2 REAR AIR DUCT Installation
11. INSTALL FRONT FLOOR SILENCER PAD (for 2WD)
(a) Install the front floor silencer pad.
12. INSTALL ACCELERATOR PEDAL (for 2WD)
HINT
Installation.
13. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation
14. INSTALL LOWER INSTRUMENT FINISH PANEL SUB-ASSEMBLY Installation
15. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Installation
16. INSTALL SIDE INSTRUMENT PANEL LH Installation
17. INSTALL CONSOLE BOX Installation
18. INSTALL CONSOLE BOX REGISTER ASSEMBLY Installation
19. INSTALL FRONT ASH RECEPTACLE ASSEMBLY Installation
20. INSTALL CONSOLE PANEL SUB-ASSEMBLY Installation
21. INSTALL NO. 1 UPPER CONSOLE PANEL GARNISH Installation
22. INSTALL NO. 2 UPPER CONSOLE PANEL GARNISH Installation
23. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
(a) Turn the shift knob clockwise and install the shift lever knob sub-assembly.
24. INSTALL CENTER LOWER PILLAR GARNISH LH Installation
25. INSTALL REAR DOOR SCUFF PLATE LH Installation
26. INSTALL FRONT DOOR SCUFF PLATE LH Installation
27. INSTALL FRONT DOOR OPENING TRIM COVER LH Installation
28. INSTALL FRONT SEAT OUTER BELT ASSEMBLY
HINT
Installation.
29. INSTALL REAR SEAT CUSHION ASSEMBLY Installation
30. INSTALL FRONT SEAT ASSEMBLY (for Standard Type Power Seat)
HINT
Installation.
31. INSTALL FRONT SEAT ASSEMBLY (for Sports Type Power Seat)
HINT
Installation
32. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)
HINT
Installation.
33. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
34. INSPECT PARKING BRAKE PEDAL TRAVEL Adjustments
35. ADJUST PARKING BRAKE PEDAL TRAVEL Adjustments
36. INSPECT SRS WARNING LIGHT
HINT
Diagnosis System.
37. INSPECT FRONT SEAT ASSEMBLY (for Power Seat) Installation
38. INSPECT FOR EXHAUST GAS LEAK