Disassembly

INTERIOR: ROOF HEADLINING: DISASSEMBLY

DISASSEMBLY





1. OPEN ROOF PANEL HALFWAY
(a) Open the roof panel halfway Manual Open Operation.





2. REMOVE DOOR SCUFF PLATE ASSEMBLY RH
(a) Using a clip remover, detach the 5 clips.
(b) Using a screwdriver, detach the 6 claws and remove the scuff plate.
HINT: Tape the screwdriver tip before use.

3. REMOVE DOOR SCUFF PLATE ASSEMBLY LH
HINT: Use the same procedures described for the RH side.





4. REMOVE FRONT DOOR OPENING TRIM COVER RH
(a) Using a screwdriver, detach the 3 claws and remove the trim cover.
HINT: Tape the screwdriver tip before use.

5. REMOVE FRONT DOOR OPENING TRIM COVER LH
HINT: Use the same procedures described for the RH side.





6. REMOVE FRONT PILLAR GARNISH RH
(a) Using a screwdriver, detach the 2 clips and remove the garnish.
HINT: Tape the screwdriver tip before use.

7. REMOVE FRONT PILLAR GARNISH LH
HINT: Use the same procedures described for the RH side.





8. REMOVE VISOR BRACKET COVER RH
(a) Using a screwdriver, detach the 3 claws and remove the bracket cover.
HINT: Tape the screwdriver tip before use.

9. REMOVE VISOR BRACKET COVER LH
HINT: Use the same procedures described for the RH side.

10. REMOVE VISOR ASSEMBLY RH
(a) Remove the 2 screws and visor.
11. REMOVE VISOR ASSEMBLY LH
(a) Remove the 2 screws and visor.





12. REMOVE VISOR HOLDER
(a) Remove the 2 holders by turning them counterclockwise.





13. REMOVE MAP LIGHT ASSEMBLY
(a) Using a screwdriver, pry out the 2 lenses.
HINT: Tape the screwdriver tip before use.

(b) Remove the 2 screws and map light.
(c) Disconnect the map light connector.





14. REMOVE ROOF FRONT CORNER HEADLINING RH
(a) Using a screwdriver, detach the 2 clips and remove the headlining.
HINT: Tape the screwdriver tip before use.

15. REMOVE ROOF FRONT CORNER HEADLINING LH
HINT: Use the same procedures described for the RH side.

16. REMOVE ROOF HEADLINING ASSEMBLY





(a) Using a clip remover, remove the 2 clips.





(b) Pull the headlining as indicated by the arrow in the illustration to detach the 4 claws. Then remove the headlining.





17. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
(a) Using a screwdriver, detach the 4 clips and 3 claws. Then remove the garnish.
HINT: Tape the screwdriver tip before use.

18. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH
HINT: Use the same procedures described for the RH side.





19. REMOVE ROOF HEADLINING ASSEMBLY CENTER
(a) Using a clip remover, remove the 5 clips.
(b) Using a screwdriver, detach the 3 clips labeled A and remove the headlining.
HINT: Tape the screwdriver tip before use.





20. REMOVE ROOF SIDE GARNISH INNER RH
(a) Using a clip remover, remove the clip labeled A.
(b) Using a screwdriver, detach the 7 clips and claw. Then remove the garnish.
HINT: Tape the screwdriver tip before use.

21. REMOVE ROOF SIDE GARNISH INNER LH
HINT: Use the same procedures described for the RH side.





22. REMOVE ROOF HEADLINING ASSEMBLY REAR
(a) Using a screwdriver, detach the 7 clips and remove the headlining.
HINT: Tape the screwdriver tip before use.