Diagnosis Display Detailed Description

NAVIGATION: NAVIGATION SYSTEM (for HDD): DIAGNOSIS DISPLAY DETAILED DESCRIPTION

DIAGNOSIS DISPLAY DETAILED DESCRIPTION
HINT:
- This section contains a detailed description of displays within diagnostic mode.
- Illustrations may differ from the actual vehicle depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle.

1. SYSTEM CHECK
(a) System Check Mode Screen

(1) Device Names and Hardware Address/*1
HINT:
- Registered device names are displayed.
- If a device name is unknown to the system, its physical address is shown instead.

(2) Check Result/*2
HINT: Result codes for all devices are displayed.

(3) Code Clear/*3

- Present DTCs are cleared.
- Press the "Code CLR" switch for 3 seconds.
(4) Memory Clear/*4

- Present and past DTCs and registered connected device names are cleared.
- Press the "Memory CLR" switch for 3 seconds.

(b) Diagnosis MENU Screen

HINT: Some items may be grayed out or not displayed, as the functions are different depending on the vehicle.

(c) Unit Check Mode Screen

Screen description:

(d) LAN Monitor (Original) Screen

(1) Check Result/*
HINT: Check results of all the devices are displayed.

(e) LAN Monitor (Individual) Screen

Screen description:

2. DISPLAY CHECK
(a) Vehicle Signal Check Mode Screen

Screen description:

HINT:
- Only items sending a vehicle signal will be displayed.
- This screen is updated once per second when input signals to the vehicle are changed.

(b) CAN Connection Check Screen

Screen Description:

HINT:
- This function operates only for the systems connected to the CAN system.
- When the engine switch is turned off, the bus lines are disconnected, or a malfunction occurs in the bus lines while the CAN connection check result is being displayed, the problem will be reflected on the screen in real time.
- If the check result is NG, the air conditioning system and advanced parking guidance system does not operate.

3. NAVIGATION CHECK
(a) Navigation Check Screen

HINT: Some items may be grayed out or not displayed, as the functions are different depending on the vehicle.

(b) GPS Information Screen

(1) Satellite information/*1
Information from a maximum of 12 satellites is displayed on the screen. This information includes the target GPS satellite number, elevation angle, direction, and signal level.
(2) Receiving condition/*2

DENSO model:

AISIN AW model:

Measurement information/*3:

Position information/*4

Date information/*5:

Vehicle signal:

Sensor signal:

HINT: Signals are updated once per second only when vehicle sensor signals are changed.

(d) Mic & Voice Recognition Check Screen

Screen description:

HINT:
- The microphone input function is on at all times when this screen is displayed.
- While recording or playing, the switches other than the stop switch cannot be pushed.
- When no voice is recorded, the play switch cannot be pushed.
- Recording will stop after 5 seconds or by pushing the stop switch.

(e) HDD Information Screen

Screen description:

Trouble code description:

HINT: This is the HDD check function in the navigation ECU.

(f) SMART Test Screen
(1) In the HDD information screen, press the "SMART Test" button, and display the SMART Test result screen.

HINT:
- It takes approximately 90 seconds for the check to complete.
- If the SMART Test result is NG, the HDD is malfunctioning.
- If the temperature is low (less than -20°C (-4°F)) or high (65°C (149°F) or more), and the HDD cannot read or write, NG may be displayed.

(g) AVC-LAN Plus Check Screen

Screen Description:

(h) AVC-LAN Plus Detail Screen
(1) This screen shows the number and time of reconfigurations.

(i) AVC-LAN Plus Diagnosis Screen

Screen Description:

(j) Sound Library Information Screen

Screen Description:

4. PROGRAM UPDATE
(a) Program Update Screen
(1) This screen is used for program updates.

HINT: For update procedures, view the new program's disc contents.