P0103
1UR-FSE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0102: Mass Air Flow Circuit Low
DTC P0102 - Mass Air Flow Circuit Low
DTC P0103 - Mass Air Flow Circuit High
DESCRIPTION
The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the valve.
The ECM uses this information to determine the fuel injection time and to provide appropriate air-fuel ratio.
Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor provide a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.
HINT: When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.
HINT: When any of these DTCs are set, check the air-flow rate by entering the following menus: Powertrain / Engine / Data List / MAF.
MONITOR DESCRIPTION
If there is a defect in the MAF meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the MAF meter and sets a DTC.
Example:
When the sensor output voltage remains less than 0.2 V, or more than 4.9 V, for more than 3 seconds, the ECM sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 3 seconds after the engine is next started.
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
P0102:
P0103:
COMPONENT OPERATING RANGE
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT: Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
PROCEDURE
1. READ VALUE USING TECHSTREAM (MASS AIR FLOW RATE)
(a) Connect the Techstream to the DLC3.
(b) Start the engine.
(c) Turn the Techstream ON.
(d) Enter the following menus: Powertrain / Engine / Data List / MAF.
(e) Read the values displayed on the Techstream.
Result:
NOTE:
*: The value must change when the throttle valve is open or closed.
C -- CHECK FOR INTERMITTENT PROBLEMS
B -- INSPECT ECM (SENSOR GROUND)
A -- Continue to next step.
2. INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
(a) Disconnect the MAF meter connector.
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard voltage:
(d) Reconnect the MAF meter connector.
NG -- CHECK FUSE (EFI NO. 2 FUSE)
OK -- Continue to next step.
3. INSPECT ECM (VG VOLTAGE)
(a) Start the engine.
(b) Measure the voltage according to the value(s) in the table below.
HINT: The transmission gear selector lever should be in the P or N position and the A/C switch should be turned OFF.
Standard voltage:
OK -- REPLACE ECM
NG -- Continue to next step.
4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
(a) Disconnect the MAF meter connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance (Check for open):
Standard resistance (Check for short):
(d) Reconnect the MAF meter connector.
(e) Reconnect the ECM connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE MASS AIR FLOW METER
5. CHECK FUSE (EFI NO. 2 FUSE)
(a) Remove the EFI No. 2 fuse from the engine room No. 2 relay block.
(b) Measure the resistance of the EFI No. 2 fuse.
Standard resistance:
(c) Reinstall the fuse.
NG -- CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK -- REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI NO. 2 FUSE - MASS AIR FLOW METER)
6. INSPECT ECM (SENSOR GROUND)
(a) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPLACE ECM
OK -- Continue to next step.
7. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
(a) Disconnect the MAF meter connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance (Check for open):
Standard resistance (Check for short):
(d) Reconnect the MAF meter connector.
(e) Reconnect the ECM connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE MASS AIR FLOW METER