Installation

PARKING BRAKE: PARKING BRAKE CABLE: INSTALLATION

INSTALLATION

1. INSTALL PARKING BRAKE NO.3 CABLE ASSEMBLY





(a) Install the 2 cable support brackets to the parking brake No.3 cable assembly.





(b) Install the parking brake No.3 cable assembly to the parking brake plate with the 2 nuts.
Torque: 8.0 Nm (82 kgf-cm, 71 in-lbf)
(c) Connect the parking brake No.3 cable assembly to the parking brake equalizer.
(d) Install the parking brake No.3 cable assembly to the body with the 3 bolts and 2 clamps.
Bolt A - Torque: 6.0 Nm (61 kgf-cm, 53 in-lbf)
Bolt B - Torque: 19 Nm (194 kgf-cm, 14 ft-lbf)





2. APPLY HIGH TEMPERATURE GREASE Reassembly
3. INSTALL PARKING BRAKE SHOE LEVER Reassembly
4. INSTALL PARKING BRAKE NO.2 SHOE ASSEMBLY Reassembly
5. INSTALL PARKING BRAKE NO.1 SHOE ASSEMBLY Reassembly
6. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET Reassembly
7. INSTALL PARKING BRAKE SHOE RETURN NO.1 SPRING Reassembly
8. INSTALL PARKING BRAKE SHOE RETURN NO.2 SPRING Reassembly
9. CHECK PARKING BRAKE INSTALLATION Reassembly
10. INSTALL REAR DISC Reassembly
11. ADJUST PARKING BRAKE SHOE CLEARANCE Adjustments
12. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY Reassembly
13. INSTALL REAR WHEEL
Torque: 103 Nm (1,050 kgf-cm, 76 ft-lbf)
14. INSTALL DIFFERENTIAL SUPPORT NO.2 PROTECTOR Installation
15. INSTALL REAR PROPELLER SHAFT ASSEMBLY (for 2GR-FSE) Installation
16. INSPECT AND ADJUST NO. 2 AND NO. 3 JOINT ANGLE (for 2GR-FSE) Installation
17. INSTALL FRONT FLOOR HEAT NO.1 INSULATOR (for 2GR-FSE) Installation
18. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 2GR-FSE) Installation
19. INSTALL HEATED OXYGEN SENSOR (for 2GR-FSE) Installation
20. INSTALL FRONT FLOOR BRACE CENTER (for 2GR-FSE) Installation
21. INSTALL REAR PROPELLER SHAFT ASSEMBLY (for 1UR-FSE) Installation
22. FULLY TIGHTEN CENTER SUPPORT NO. 1 BEARING ASSEMBLY (for 1UR-FSE) Installation
23. INSPECT AND ADJUST NO. 2 AND NO. 3 JOINT ANGLE (for 1UR-FSE) Installation
24. INSTALL FRONT FLOOR HEAT NO. 1 INSULATOR (for 1UR-FSE) Installation
25. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1UR-FSE) Installation
26. INSTALL REAR NO. 1 FLOOR PANEL BRACE (for 1UR-FSE) Installation
27. INSTALL FRONT CENTER FLOOR BRACE (for 1UR-FSE) Installation
28. INSTALL FRONT FLOOR COVER CENTER RH (for 1UR-FSE)
29. INSTALL FRONT FLOOR COVER CENTER LH (for 1UR-FSE)
30. INSTALL CONSOLE BOX (for 4WD) Installation
31. INSTALL CONSOLE BOX REGISTER ASSEMBLY (for 4WD) Installation
32. INSTALL CONSOLE BOX PLATE (for 4WD) Installation
33. INSTALL INSTRUMENT PANEL FINISH LH PANEL END Installation
34. INSTALL INSTRUMENT PANEL FINISH RH PANEL END Installation
35. INSTALL FRONT ASH RECEPTACLE ASSEMBLY Installation
36. INSTALL CONSOLE UPPER PANEL GARNISH FRONT Installation
37. INSTALL FRONT SEAT ASSEMBLY
HINT: Refer to the instructions for Installation of the front seat assembly Installation.

38. CONNECT BATTERY NEGATIVE TERMINAL
NOTE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

39. INSPECT PARKING BRAKE PEDAL TRAVEL Adjustments
40. ADJUST PARKING BRAKE PEDAL TRAVEL Adjustments
41. INSPECT SRS WARNING LIGHT
Diagnosis System
42. CHECK FOR EXHAUST GAS LEAKS