Disassembly

DIFFERENTIAL: REAR DIFFERENTIAL CARRIER ASSEMBLY (for 4GR-FSE):

DISASSEMBLY

1. REMOVE REAR DIFFERENTIAL BREATHER PLUG






(a) Remove the breather plug from the differential carrier cover.
2. REMOVE REAR DIFFERENTIAL CARRIER COVER






(a) Remove the 8 bolts from the differential carrier cover.






(b) Using a brass bar and hammer, lightly tap the rib of the side bearing retainer to remove it.
NOTE: Do not damage the sealing surface of the differential carrier.

3. REMOVE REAR DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR BOLT






(a) Remove the bolt and oil deflector from the differential carrier cover.
4. SECURE REAR DIFFERENTIAL CARRIER






(a) Set the differential carrier to an overhaul stand, etc., as shown in the illustration.
5. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR Component Tests and General Diagnostics

6. INSPECT DIFFERENTIAL RING GEAR BACKLASH Component Tests and General Diagnostics

7. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION Component Tests and General Diagnostics

8. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH (for 2WD) Component Tests and General Diagnostics

9. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE Component Tests and General Diagnostics

10. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD Component Tests and General Diagnostics

11. INSPECT TOTAL PRELOAD Component Tests and General Diagnostics

12. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL






(a) Using SST, remove the 2 oil seals.
SST: 09308-00010
13. REMOVE REAR DRIVE PINION NUT






(a) Using SST and a hammer, unstake the staked part of the drive pinion nut.
SST: 09930-00010
- Be sure to use SST with the tapered surface facing the shaft.
- Do not grind the tip of the SST with a grinder, etc.
- Completely loosen the staked part of the nut when removing it.
- Do not damage the threads of the drive pinion.





(b) Using SST to hold the flange, remove the drive pinion nut.
SST: 09330-00021
14. REMOVE REAR DRIVE PINION COMPANION FLANGE (for 2WD)






(a) Using SST, remove the companion flange.
SST: 09950-30012
09951-03010
09953-03010
09954-03010
09955-03030
09956-03030
NOTE: Apply grease to the threads and tip of the SST center bolt before use.

15. REMOVE REAR DRIVE PINION COMPANION FLANGE (for 4WD)






(a) Using SST, remove the companion flange.
SST: 09950-30012
09951-03010
09953-03010
09954-03010
09955-03030
09956-03020
NOTE: Apply grease to the threads and tip of the SST center bolt before use.

16. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR
HINT: Perform this procedure only when the dust deflector is damaged.

(a) Using SST and a press, remove the dust deflector.





SST: 09950-00020
SST: 09950-60010
09951-00380
SST: 09950-70010
09951-07100
NOTE: Do not drop the companion flange.

17. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL






(a) Using SST, remove the oil seal from the differential carrier.
SST: 09308-00010
18. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER






(a) Remove the drive pinion oil slinger.
19. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING






(a) Using SST, remove the inner race of the rear drive pinion front tapered roller bearing from the drive pinion.
SST: 09556-22010
NOTE: Apply grease to the threads and tip of the SST center bolt before use.

20. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER






(a) Remove the drive pinion bearing spacer.
21. REMOVE DIFFERENTIAL CASE ASSEMBLY






(a) Put matchmarks on either set of the bearing cap and differential carrier.
(b) Remove the 4 bolts and 2 bearing caps.
NOTE: Do not swap bearing caps, as each cap is only suitable for its original location and installation direction on the carrier it was manufactured on.





(c) Using SST and a hammer, remove the 2 side gear shaft plate washers.
SST: 09504-22011
NOTE: Put identification marks on the side gear shaft plate washer to show the location for installation (back side or teeth side), or keep them separate so that they can be distinguished.
HINT: Measure the thickness of the plate washers and note it.





(d) Remove the differential case assembly and the case bearing outer races LH and RH from the differential carrier.
- Do not damage the differential case bearing or ring gear.
- Put identification marks on the case bearing outer race to show the location for installation (back side or teeth side), or keep them separate so that they can be distinguished.

22. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING
(a) Remove the drive pinion from the differential carrier.






(b) Using SST and a press, remove the inner race of the rear drive pinion rear tapered roller bearing from the drive pinion.
SST: 09950-00020
NOTE: Do not drop the drive pinion.
HINT: If either the drive pinion or ring gear is damaged, replace both as a set.

(c) Remove the drive pinion plate washer from the drive pinion.
HINT: Measure the thickness of the plate washer and note it.





(d) Using a brass bar and a hammer, remove the outer race of the rear drive pinion front tapered roller bearing from the differential carrier.
NOTE: Place the brass bar onto the outer race of the rear drive pinion front tapered roller bearing. Do not damage the differential carrier.

23. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING






(a) Using a brass bar and a hammer, remove the outer race of the rear drive pinion rear tapered roller bearing from the differential carrier.
NOTE: Place the brass bar onto the outer race of the rear drive pinion front tapered roller bearing. Do not damage the differential carrier.

24. REMOVE DIFFERENTIAL RING GEAR






(a) Hold the differential case in a vise between aluminum plates.
NOTE: Do not overtighten the vise.

(b) Put matchmarks on the ring gear and differential case.
(c) Using a chisel and a hammer, unstake the 5 lock plates.






(d) Remove the 10 ring gear set bolts and 5 lock plates.






(e) Using a plastic hammer, tap on the ring gear to separate it from the differential case.
HINT: Use cloth to prevent damage to the ring gear teeth.

25. INSPECT RUNOUT OF DIFFERENTIAL CASE ASSEMBLY Component Tests and General Diagnostics

26. REMOVE REAR DIFFERENTIAL CASE BEARING (for 2WD)
HINT: Perform this procedure only when replacing the case bearing or differential case.





(a) Hold the differential case in a vise between aluminum plates.
NOTE: Do not overtighten the vise.

(b) Using SST, remove the case bearing inner races LH and RH from the differential case.
SST: 09950-40011
09951-04020
09952-04010
09953-04030
09954-04010
09955-04061
09957-04010
09958-04011
SST: 09950-60010
09951-00480
09951-00350
09952-06010
NOTICE:
- Do not deform the bearing cage if the bearing is to be reused.
- Hook the SST claw from the dent of the differential case to the bearing inner race.
- Apply grease to the threads and tip of the SST center bolt before use.

27. REMOVE REAR DIFFERENTIAL CASE BEARING (for 4WD)
HINT: Perform this procedure only when replacing the case bearing or differential case.





(a) Hold the differential case in a vise between aluminum plates.
NOTE: Do not overtighten the vise.

(b) Using SST, remove the case bearing inner races LH and RH from the differential case.
SST: 09950-40011
09951-04020
09952-04010
09953-04030
09954-04010
09955-04061
09957-04010
09958-04011
SST: 09950-60010
09951-00480
09951-00330
09952-06010
NOTICE:
- Do not deform the bearing cage if the bearing is to be reused.
- Hook the SST claw from the dent of the differential case to the bearing inner race.
- Apply grease to the threads and tip of the SST center bolt before use.

28. REMOVE DIFFERENTIAL PINION AND SIDE GEAR (for 4WD)






(a) Hold the differential case in a vise between aluminum plates.
NOTE: Do not overtighten the vise.

(b) Using a pin punch (3 mm) and a hammer, remove the straight pin.






(c) Remove the following parts from the differential case.
- Differential pinion shaft: [A]
- Differential pinion : [B]
- Differential pinion thrust washer: [C]
- Differential side gear: [D]
- Differential side gear thrust washer: [E]





(d) Remove the differential pinion shaft from the differential case.






(e) Remove the 2 differential pinion gears and 2 differential pinion thrust washers from the differential case.






(f) Remove the 2 differential side gear and 2 differential side gear thrust washers from the differential case.
29. INSPECT DIFFERENTIAL PINION AND SIDE GEAR (for 4WD) Component Tests and General Diagnostics

30. INSPECT DIFFERENTIAL CASE ASSEMBLY (for 4WD) Component Tests and General Diagnostics